Quantcast
Jump to content

Recommended Posts

Posted

Noticed it this morning, Was -1 out, Started it with choke half way open, Fired right up second crank via electric starter. Shed was filling with not exhaust but oil/smoke, thought nothing of it at the time, Fast forward to later today, Started it up after washing it, And got a big puff of smoke from the bike, Checked the oil, Sure enough was down about half a quart, Opened air box, Oil sitting in the bottom of it (could have been from the prefilter though but there was an oilish trail from the intake tube which the breather connects to) Breather tube has milky white oil (I know it means water) Any ideas or help would be apreachiated, It has great compression which strikes me as odd considering its used half a quart of oil in about 5 hours run time (Have a hour meter)

Posted

Only has one vent line off the crankcase, and it does not seem to have a valve so its constantly getting pressure out it, I have a feeling thats where some of the oil in the air box is coming from,

Posted

I noticed this as well on my 1990 Big Bear after full fluid change and filter cleaning. Before the oil change, zero smoke at start-up/idle.

Afterwards, smokes a bit on initial start but clears up after warmed up.

Kind attributing to the fact that maybe poor oil circulation due to very clogged oil filter in my case and age of the bike systems.

Planning on valve adjust but not sure that will make any difference in start up smoking. I'll be watching for additional tips too.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By HoldenBoy
      Hi all,
      Looking for some help on a starter/bendix issue. Can Am outlander 450 2017. While cranking to start, the starter spins and engages into the ring gear. After a few seconds the bendix retracts while still spinning and there is no damaged teeth on the drive pulley.
    • By rjsummer
      Just picked up an 84 LT185 ATV, I understand there was an accessory add  on that gave it electric start, anyone have any info about that kit? 
    • By crankin
      I have a 1997 Yamaha Big Bear 350 4x4. It used to start right up. Then all of a sudden it wouldn't crank. I have a schematic for it so I started tracing the problem. I had no power at the starter solenoid. According to the schematic the power comes from the neutral switch and through the starter circuit cut out relay. I cannot locate the cut out relay on this machine.. If I apply power to the relay it will crank with the start button.
      The neutral switch is hard to get to with all the brackets on this thing. I did find out from all my research that if I apply the rear brake lever it will start.
      Does anybody know if the cut out relay exists and where it might be found?
    • By marlon smith
      1990 kawasaki bayou 300c idles fine but pops out exhaust and intake when trying to excel, will not take throttle past 1/4 , any one had this problem?
      have replaced carb twice, same thing, fresh built engine cylinder head, same as before, new spark plug, flywheel key is good, pulser test good, good spark
    • By cruteg8
      Does anyone know forsure if u can swap out the Crank Case on a 2001 kawasaki Lakota 300 sport  with a kawasaki Bayou 300 Im seeing yes and no all over some say the mounting position is different so you can't swap the cases but everyother inernal engine part you can swap then im seeing no problem bolts right on can someone plz clarify who knows forsure 
×
×
  • Create New...