Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
By Mike Johnson
Does anyone know what the 3rd item is behind the battery on this ATV ? I know 1 is the, solenoid1 is the CDI box, what is the 3rd.
By Scott Sirr
I need to figure out how to clean/fix or replace my neutral switch assembly On my 2008 Yamaha big bear 400 as generally the neutral light doesn’t come on when it is in neutral. To get it to come on I have to wiggle the foot shifter and hold it in just the right spot.
I have googled it and can’t find much on the 400’s. I can’t find a service manual online and the parts manual is super vague.
I think it is in the right side engine cover area, but not certain.
Any help would be great. thanks
By Daniel Gibson
Working on a bayou 220 that has been ran extremely hard it's whole life. Literally had almost an inch thick dirt/oil covering the motor. Yeah that bad. Surprisingly it runs though. I cleaned the carb and tank multiple times. They're clean enough to eat off of. Readjusted valve lash and set timing. Was about 3 teeth off. It cranks good and runs good only problem is I have to cover the carb intake basically choking the hell out of it for it to start. The com choke works fine. It does this each time I start it regardless of temperature both ambient or motor. Wth? Compression is at 115psi I get 130s if I put a little oil in the piston chamber. Please help. Thanks
My Honda Fourtrax won't start. The starter is kicking the engine over, but it won't start. It sat for about a year while I was living away, so I thought it might have been bad gas. I completely drained the fuel, flushed the fuel lines and filled it with fresh gas. However, still nothing. It started and ran fine the last time I used it. Any suggestions on how to diagnose this? It could be fuel or electrical at this point. Is there an easy way to rule one or the other out? Thanks
I was looking online and saw some cool lifted ATVs and figured I'd start a topic. Please post if you have pics or if you find some cool lift kit ATV photos or videos online, let's keep the topic going. I just added this one in the gallery but you can just add them in this topic also.
Similar Tagged Content
Good after noon everyone, new here and really sure how to post anythang or get back to the topic I was lookn for so maybe u quad fans can help me out. I've got a 300 king quad that I really need info on. It's drivin me nuts . It starts and idles great but when I give it gas it spits and sputters. Anyone that could help me get lined out on this forum and my old quad u be a blessing .
Hi, me and my friend were out and riding the other day and filmed some so I tried to do an edit from the videos that I got. So this is my first ATV edit and I need you guys to tell me what I can improve in my filming and editing. Please give rewarding comments!
1983 Yamaha YT175
Fired up for the first time after total rebuild. Now I have no idea whats going on. Compression is 120, new plug, new fuel and oil lines, new choke and fresh fuel. Carb cleaned and reeds are good (no gaps).
Will not start without choke and stalls out when choke is off. Played with choke adjustment and doesn't change.
It fires up first pull and only idles if I play with idle screw. As soon as I touch throttle, it goes bezerk on me and I have to shut it down as you can see in video .......
You can here the recoil lever tinging in the video. I lost the spring. D"oh!!
So far I have swapped ignition coil, spark plug, CDI with no change. I have removed flywheel to check keyway and it is where it should be.
Checked resistance on stator ... I get 10ohms +/- 10% on pickup coil within specs as per manual and I get 273ohms on charge coil. Manual states 300ohms +/- 10%, so that is also within spec.
I have also swapped out jet needle and played around with different settings. Eventually I put it back to the 3rd line.
The engine already has new seals and bearing so I am completely baffled as to what I am missing here.
Any and all suggestions will be appreciated.
I have also swapped carbs from a running YT175. Same results.
Recently Browsing 0 members
No registered users viewing this page.