Quantcast
Jump to content


2006 Yamaha Wolverine - Cold Idle Issues


skeeziix

Recommended Posts

2006 yamaha wolverine 450 carb cold idle issues it stays running when I have the choke up but when I put it back down to idle it wants to stall out. This machine only has 218 miles had has pretty much been sitting for that long lol. Runs great in the warm but is really rough in the cold.

I am going to try to change the gas, new air filter, and spark plugs.

Any and all suggestions are welcome.

Link to comment
Share on other sites

spark plug is a good change, you could add some seafoam, available i think from your napa stores, it will clean the carb without having to take it apart. im sure thats whats wrong with the cold start. you could also put a hotter plug in too, i think yours is an NGK DR8EA, a hotter plug would be DR7EA ... just use it when its cold if you decide and replace it with the summer plug in the warm months

Link to comment
Share on other sites

sounds like ya got it all covered ..lol.. with the newer fuel and all the extra things they have to do to it to cut down on emissions it will start to go bad in as little as 30 days ... especially in small amounts like in out atv tanks .. I always put a fuel stabilizer in mine so that I don't have to remove and clean/rebuild 2 carbs .. its cheap insurance on a good running quad even after sitting for months at a time ...

Link to comment
Share on other sites

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Spritee1
      having an issue with the unit when running under a load up a hill or in high gear, seems like the belt is slipping, there is a clapping sound coming from the primary clutch like it releases and snaps back in. i don't think I should have a noise like that. this is a friends unit and he has already replaced the primary twice with the same result.
      not sure where to look next
    • By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
    • By ResQ91
      Hi guys
      My 87 Bear 350 won't start and could use a hand.
      Turn key on and Oil light turns on and then slowly fades out. (I think this is key to this) No start, not even a tick.
      battery and connections good
      A Solenoid post jump turns it over
      Neutral Safety Switch wire attached and seems good
      It has not had a wire/switch on Rear Brake Pedal ever since I had it.
      Any thoughts on some other things to troubleshoot this??
    • By 1998Zuki250
      Anyone here ever have any issues with the law for riding on public land? Im in upstate NY and they seem to ruin everything so Im over cautious. 
    • By N00bie
      From Arkansas. Just bought a 2012 Gator 850i RSX because I could not pass up the price. BUT it has an idle problem. So, to be honest, I joined just to get a service manual. I have a choice: 1)Buy a hard copy: ~$100; 2)Buy a CD ~$35.00; Get a direct download for free posting 10 times; or get a download for $29.00 (subscription). Haven't decided what to do yet.
×
×
  • Create New...