Quantcast
Jump to content

2000 Yamaha Bear Tracker - Bad Pickup Coil

marmster

By marmster
in Yamaha ATV Forum

 Share

Recommended Posts

marmster Newbie

marmster

Posted
Posted

I have a 2000 Yamaha Bear Tracker 250cc. I tried to get my machine running after storing it for the winter and there was no spark. After running through the electrical tests in the service manual it led me to the stator. I am getting a reasonable resistance for the source coil (320 ohms) but a bad reading for the Pick up coil (13000 Mohms). does anyone have any experience with just replacing the pickup coil. I saw them available on ricky stator. If anyone could provide me with some insight as to doing so that would be great.

slickerthanyou Contributor

slickerthanyou

Posted
Posted

I have had no luck with Ricky stator products and also know quite a few others with bad out of the box stuff. I would steer clear of that brand. I can tell you I have great luck with just replacing a pickup, source or lighting coil. I use ricksmotorsports.com for my electrical needs and have never had an issue with a bad part. If you feel comfortable with working with Electrical stuff I say do it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Forum Topics

    • cavry
      03 Recon 250TM (Manual) locking up
      By cavry
      O3 sat a while. Engine is running fine. I got it into neutral, did some general tune-up and cleaning then pulled the shifter pedal up and it locked up and will not release into neutral again.  Does anyone have experience with this problem?  Thanks for looking and any help.
      Cavry
    • 88bigbear
      1988 big bear 350 no spark
      By 88bigbear
      Bought a 88 big bear 350 4x4 took it for a run and lost spark, found it was stator so I replaced that then took it for a long run and it sat for 2 days and no spark again, this time stator tests good on ohms and voltage for source and pick up coils so I started replacing things including regulator, ignition, ignition coil and plug cap, spark plug and everything tests great including all safety switches until the orange wire for ignition coil from the cdi it only reads 3 volts so I replaced the cdi and still 3 volts, any ideas??
    • cfherrman
      1988 Yamaha 350 Big bear No spark
      By cfherrman
      Fixing for a friend. Atv was at a different friends house to be fixed and he rebuilt the carb and had it running nice, then it shut off and no more. He replaced the key and the coil.
       
      So he got busy, so I am helping, I checked the wiring from the stator to the cdi, and from the cdi to the coil. All is good. I checked resistance on the pickup coil, good, and on the source coil, open. I buy a new stator (China) and the 4 prong plug only has 3 wires in it while mine has all 4. I checked resistance in the source coil and it's in the 300's. I pulled one of the old pickup wires out of the old stator and wire it in the new one. Still no spark.
       
      Why do the wires differ, I checked the VIN again and it's "J" for the year and I got a 1988 stator. Please help!
    • LashinWheeler
      2006 Polaris Sawtooth No Spark
      By LashinWheeler
      Hello all, I have a 2006 Polaris Sawtooth with no spark. It has a dead battery but with a jump pack on it, it will still not Spark. Plug is good, Throttle ETC is not closed, Stator pick up coil seems to Ohm out in the correct range, Unsure how to properly check the CDI. And when ignition is on the Neutral and reverse light come on but after cranking just the neutral stays on. 
       
      Any help would be great,
       
      Thanks!
    • OldATVowner
      99 Bear tracker no neutral or reverse light or start button
      By OldATVowner
      Just getting into this issue really. Been replacing solenoids but now I'd like to track down the problem. This time I'm not getting neutral/reverse lights or start button. Was on a creek ride when it started doing this recently. It cranks by arcing the solenoid and gives me no light or start button but if I crank with the pull cord....the neutral light and the button work. Turn it off and try to crank with the key and nothing. I'm looking into the safety switch issue tomorrow and re charging the battery. Just figured this was odd enough of a problem that you guys might be familiar. Thanks

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...