Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
My retaining wall fell 20 feet up my driveway from the entrance. I called my insurance company and was told that there isn’t a lot they can do.
So I called the town to see who built it and the old homeowner did 4 years ago! With no contractor! And the building department passed it for inspection.
There is no geo grid, no drainage, and dirt as a backfill. I bet you I can pull the rest down by hand.
My question is who is responsible? This is not right.
Sent from my iPhone using Tapatalk
By Christian Smith
Recently bought a Polaris 425 Xpedition. Main issue is that the quad randomly misfires sometimes. ONLY does it at idle. Everything sounds good. What should I look for? Haven't checked the plug, seems a bit hard to get to, not sure. Headlights flicker at idle as well, is this a sign of a weak stator? Help?
Over the years I have always used a friends machine, and only ride a few times a year. Last week I purchased a 2002 Polaris Sportsman 700. The front diff needs a rebuild, the axles are very loose where they go into diff. My question is, both front wheels rotate forward by hand, but do not rotate the opposite direction. Is this "NORMAL OPERATION" I plan on rebuilding the hubs at the same time as the diff.....
My question about the rear diff, it rolls as if the machine has a total POSI rear axle...……. I lifted the front end off the garage floor with overhead hoist, as I moved it sideways the rear tires skidded rather than rotate. Both would roll forward easy, but not go in a circle. When I drove the machine in the garage making a tight turn I could feel the binding and skidding of rear tires.... Even if the switch was in 4 wheel drive, when it's hanging in te air the ignition is off...….. with the machine in 2 wheel drive mode, is that HONESTLY 1 wheel drive to allow turning without tearing up the lawn? then it locks the rear axle once it's put into 4 wheel drive? I'm guessing the rear diff needs a rebuild also because there is something "BALLED UP" internally locking the rear wheels together?
It's a old machine that was not maintained, I thought the wheels were all rusted, but it was 17 years off baked on red clay. Just wanting to make it a reliable machine. I have great mechanical ability, just lacking a little knowledge of what is suppose to be "NORMAL OPERATING STANDARDS"
Thank you in advance for sharing your knowledge.
Got a good deal on an 89 bayou 300. Couple questions. First is in the picture I have posted. Note the two wires at the bottom of the pic (white and black/yellow). They were not hooked up to anything and Im not sure if they are supposed to go to the battery or somewhere else and what they are for.
Second question is I had the carb apart for a cleaning. The vaccum operated slide has a spring under the cap with a plastic clip that goes inside the spring. Is there a proper location inside the spring for that clip. Right now it is just below half way inside the spring.
It runs alright but keeps fouling the plug. Pulled the plug off, cleaned it and dried it off and it starts back up but not sure how long before itll do it again, last time it was about 20 minutes of riding and it bogged out and wouldnt start.
Just bought a used 2014 outlaw 90.
I noticed at the top of the front shocks there is 2 mounting holes for the shocks. By the markings the shocks used to be mounted in the inner holes now the shocks are mounted using the outer holes. Googling I can't find the reason for these two holes.
2nd question is about the rear suspension
When I push the suspension down it is very slow at raising back up. Should it be slow? Is it a safety thing for kids so it doesn't bounce them off. The spring adjustment is on the second lob from softest. Has painted arrows so I'm guessing it's from factory.
Has anyone touched one of these machines and could tell me if this is normal?
Similar Tagged Content
Just thought I'd start a new thread for newbies to the site!
If you're new here, tell us who you are, where you're from and what you ride!!!
Lets get to know each other a little better shall we?
I'm not new to the site, obviously, but...
I'm Kristin from Denver!!! I ride a 2008 Yamaha Rhino. She's my muddy baby!!!!!! Several aftermarket parts on her. She's good to me! We try and ride every weekend. This weekend we're off to MOAB! :woot:
hello riders,new guy in the house.i am a owner operator of a custom metal polishing shop,located in southeast indiana.i live to polish and love to ride!!
If you have any nasty looking parts that you might want to refinish hit me up,carbs,rims,trees,lower legs,swingarms,cylinders,heads,covers well you get the idea.
For more info pm or email me i will hook you up!!!
Recently Browsing 0 members
No registered users viewing this page.