Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
By Alan Callison
Hello boys and girls!:howdy:I need a little help if ya dont mind.I need to replace the rear axle bearings on my 400 but Im going at this blind having never done it before. Ive looked it up in the repair manual but it doesn't give any specific steps on how to do it. I've got the left rear brakes off already as I was replacing the shoes anyway. Can somebody give me a rundown on what Ive gotta do please?I know I need to pull the right wheel off just havent done that yet. Do I need to take anything apart in the final drive or elsewhere in order to yank the axle out for instance? Which side does the axle come out from,L or R? Any details I need to know will be greatly appreciated.Thanks ya'll!
By Frank Angerano
So here’s a question. I have seen a few members that have recently purchased a used bike. Also a HUGE amount of so called new members who have purchased a used bike and have come here “just here for a manual”.
Some have been disappointed with the bikes and or knew they were getting a broken bike with some mechanical experience thinking hey I can fix it. So here’s my take on buying a used bike. Anyone who has followed some of mine and other members posts about what to look for when buying a used bike here’s a few pointers on what to look for.
1. I always check the oil and look for moisture, metal shavings and color.
2. Feel the compression or take a compression tester with you.
3. Check for spark (if the bikes not running)
4. Take a small jumper pack to verify that the starter cycle works and the bike cranks.
5. Look for bent or cracked frame/welding that was done on the frame from maybe a wreck.
5. Mismatch plastics by looking under neath.
7. Bolts on the engine/frame that look like they are stripped from someone taking the bike apart.
8. Any kind of scilicone or gasket adhesive that was used on a cover plate or engine seem where the engine was taken apart.
9. Patches on the exhaust pipes with sheet metal or jb weld patch material.
10. Wiring messes on the harness like bundles of tape where the harness was opened up and taped up for an after market device or just plain butchered up.
11. Put the bike in gear (running or not) and roll the bike back and forth to see that the gears work and you feel resistance like the engine is trying to spin while pushing it forward as if you were push starting it
12. I keep a vin# decoder website on my phone as a favorite to double check the year of the bike .
All though nothing is fool proof these tips will help you along while buying a used bike. Not only that but it will help you negotiate a fair price for a bike that may have one of the above problems.
I have minimized this entire process down to about 15 mins. I buy all the time so I don’t expect you to do the same or have a compression tester etc but use some of these tips when buying and go into the purchase with confidence!
I would like to hear anyone else that has any input on buying a bike and what to look for!
I'm really considering this utv. Before any negative comments about this machine remember I did everything I wanted with a 250 Ozark. My 09 rubicon was over kill. I'll use it for snow plowing bulldozing logging and cruising. So I can spend 8,500 on a ruby or the 500 pioneer.
Similar Tagged Content
Was using the quad the other day to shuttle wood from my pickup to my wood pile. When the job was done I turned off the Quad and heard a bit of a racket from the front end. When I got down underneath the sound seemed to be coming from the fan housing. fan was moving in spurts and not quickly... much like a computer case fan that's had it's day. What I know.
Temp sensor is ok, as the fan tries to activate fan is getting some voltage as it is attempting to spin. When I first bought it used I tested the fan direct to battery and it was fine. The fan was working ok even not direct wired as I went on a couple of rides and when stopped and idling the fan did run Seems to be free spinning with my finger read up in the manual and they require me to drop the rad. now I'm not opposed to that as the rad has some damaged areas I want to try and straighten out. But if I can get the fan working without, I can leave the rad as it is until next year.
Fan assembly is about 300 bills, any work arounds or alternatives? I even thought large computer case brushless fan. smaller ones are about $7 larger ones better quality probably far below the 300. They run standard 12v DC.
Anything I should be doing before dropping the rad... other than check for obstructions even though it seems to spin, and trying to hardwire it to the battery again for a test to see if it acts the same?
By Guest Fox300exchic
The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
I need to know what I have and what tire really go on it, Mine has 24x11x10 on the back and 22x8x10 on the front and I need new tire but I don't think are the right size. Also I can't find the model number listed but it looks like a 250 quadrunner 2wd and I think it is a 1987 maybe, can anyone help me, also I it has a rich running sound and I put a carb diap in it and cleaned the carb. is there a jet needing replaced?
Recently Browsing 0 members
No registered users viewing this page.