Search the Community

You guys are my last resort. Got a 2000 prairie 300. Brand new battery, neutral switch, aftermarket carb, spark plug, silenoid, key switch. Fuses are good. No neutral green light, will crank if cross the silenoid, but won’t start. No power at the ignition switch or regulator. I’m thinking cdi box or starter relay. Anyone have any suggestions?

I got a prairie 700 and it wont spark. I e changed all things electrical and im outta ideas and was wondering if anyone has any tips or trivks with this bike? ie. grounds that go bad or common spots for shorts.

I have this ATV that was given to us by sister inlaw...and look like the fuel filter fell out when drive around....but i can find anything on that system. if anyone could be soo AWESOME to please post manual and/pr pick of where the fuel filer goes that would b GREAT!!!! Thank you all for any help!!!!!!!!

Hello all, I have a Kawasaki that will idle perfect but won’t go over 10 mph. Reset limp mode, checked belt sensor, it will go into 4 wheel drive but won’t rev up more than 2500 rpm’s. I have no lights blinking. Ran perfect for months until I let it idle while cutting limbs on the trails. Had a new carb, air filter and gas, just won’t rev up. Assistance would be appreciated.. tks

Picked up a 2000 prairie 300 4x4. It is leaking out of the rear output seal where the driveshaft contacts to the engine. I'm havi g a really hard time finding out how to remove the driveshaft online, finding a service manual, and finding the seal on a parts diagram. Anyone know how to remove the driveshaft or know where a service manual is for it? Thanks

So my prairie 360 4x4 won’t run right out a new carb on and it would drive fast for like 2 mins and after that if you try to give it to much gas it just pops and won’t let it rev high

This is my 1st atv project... I'm use to trucks. I have replaced both fuel lines and it's not leaking from there anymore. I cleaned out carb and it's not leaking from there. Nowhere round hose's and carb are wet...it looks like it's leaking from bottom of atv... I'm baffled. I hope someone can help

I have recently bought a kawasaki kvf650 4x4 . They are marketed as a brute force or a prairie. Same bike . Im needing to find the chassis number for it so I can order a few parts required . The local dealer has said bring it to them they will find it but it will cost money to do so . Cheaper and easier to find it myself . Its not between the A arm mount points which is where they are supposed to be ..

Does anyone have a lead on a Rear Diff for a Prairie 300? My case cracked!

hi everyone. recently iam get a good vibration that comes and goes while iam riding my praire 4x4. iam afraid something is going to detonate. vibration is felt in the steering and then you will here a noise and this comes and goes. its very noticeable when iam on a blacktop surface. iam worried. i cant get any slop in the drive joints i can grab onto. so any input would be appreciated. i have a manual downloaded and i,ve went through it pretty good. my thought is its from the output shaft to the front drive. let me know if anyone has experianced this.

View File 1999-2002 Kawasaki KVF300 Prairie Service Manual 1999-2002 Kawasaki KVF300 Prairie Service & Repair Manual Submitter Spartacus Stroppel Submitted 08/25/2019 Category Kawasaki ATV  

Just bought Kawasaki Prairie 650 vtwin 2002 and replaced old carb with new, but the bolts to hold down the air housing are missing. Anyone have any idea what size they are? I apologize for not being very mechanically inclined. Any help would be much appreciated.

I'm looking to buy a used 99 Prairie 400 Auto 2X4. Anybody know what things I should check or problem areas for this model?

1997-2002 Kawasaki Prairie 400 Service Manual View File 1997-2002 Kawasaki Prairie 400 Service Manual Submitter oxidized_black Submitted 12/14/2016 Category Kawasaki ATV  

Hey Everyone, new to the site. Hoping someone can send me or direct me to a repair manual for 2002 Kawasaki Prairie 650. Any help would be appreciated.

I most have a rare ATV, because I can not find a service manual without paying money to Kawasaki. It's a 2005 Prairie 360 2x4. 4x4 manuals are all over the place, but nothing for a 2x4 . Heck, Bike Bandit doesn't even list parts for a 2x4. Any suggestions besides paying Kawa. My machine is in limp mode and I've yet to find an applicable video or even procedure.

Hi Guys, I purchased a 2001 Kawasaki prairie 400 for my son, the machine runs great but had issues with bent rims. I bought a set online knowing that I would need 2" wheel spacers for the rear tires. My issue now is the hub (lug) studs are too short for the spacers that I have. Does anyone know where I can get longer studs that have the same pitch as stock? OEM studs are 10mm x 29.5mm with 1.25mm pitch, I'm most likely looking to get 10mm x 44mm studs. Any help would be appreciated. Andy

Smells like gas in the oil ... Also, recently replaced belt, new BT does not have grooves on both sides, does that pose a problem? Also just bought and replaced new carburetor, never has it idled better, but give it gas and it backfires very loudly!

My 2006 Prairre will only start with a shot of starting fluid. Any ideas or suggestions of what might be the problem?? Thanks.

I have an 05 2x4 Prairie 360 that is now in "limp mode". I happened when I my son was riding it and I didn't discover it until some time later. After hours of searching, the only service manuals I can find are for 4x4 and they recommended procedures are not applicable to my model. There is a manual on this forum but I can't download it until I get 10 posts, replies, etc.

My 2005 Kawasaki Prarie 700 will not go over 27mph, seems to have low to no throttle response, dies out whenever you don't keep the throttle up, seems to have no power, and the 4x4/2x4 light keeps flashing back and fourth and also there's a red light on that I'm not sure what it means, any help would be greatly appreciated