Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

innosol80

2005 Sportsman 800 efi brake lights not working

Recommended Posts

The brake light son my ATV are not working. I replaced the brake light switch and still nothing. Any ideas? Thanks.

Share this post


Link to post
Share on other sites


Your Welcome,

Even goofballs get lucky sometimes !! :wink:

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Sturgeon
      Hello everyone, did a search and not successful. Purchased new 2017 Sportsman 570 sp and my power steering is not working. Seems to have a mind of it's own. Works then it doesn't. Dealer says there's not a fix. Thought it was just me and it being a brand new machine with 4 hours on it. Dealership said it's this model only ? Not sure what a person in this spot is suppose to do and wondering are your thoughts mite be. Thanks 
    • By Frank Angerano
      I’m looking for any member that may be familiar with the neutral safety switch on this bike.   
      I picked up a bayou 220 that I found sitting in a shed. Nice looking bike the guy said it would not start one day and put it away and never touched it again.  
      So it turns out the neutral safety switch is bad.  I jumped it out and the bike fired up and runs good.  
      I’m more then capable of the work in changing it but this thing is buried pretty good. I’m curious if anyone has done the switch replacement before? 
      I attached some pics to see.
      picture 1 is the side view you can see the green and red wires going into the cover. 
      Pic 2 shows looking down on the drive shaft coming out of that cover.  That is not a simple cover you just pull off. 
      Im wondering how deep and how much shit has to come off like the drive shaft etc for this switch  to be replaced. 
      So if any of the QC members have done this switch I’m looking for any input with regard to changing it.  
      Thanks. 


    • By mike rhoades
      View File Polaris 1996-1998 ATV Light Utility Service Manual
      Service manual for 1996-1998 Polaris ATVs and light utility vehicles covers: Magnum 2x4, Trail Blazer / Scrambler, Sportsman 4x4, Magnum 4x4, Trail Boss / Sport, 6x6 / Magnum 6x6,  Xplorer 300 / Xplorer 400, Sportsman 500 & Xpress 300 / Xpress 400
      Submitter mike rhoades Submitted 03/02/2019 Category Polaris ATV  
    • By crf250r
      good day everyone, 
                        new to this page. I need help with my 1994 fourtrax 300 4x4. the bike stop sparking for some odd reason so no big deal I order a new ignition coil, that was not it so I order a new cdi box. now I get sparks. by now the battery is low from cranking so much, so I boost it with the truck. the bike as the hardest time to start and when it does it runs rough, bogging, backfire,..., reverse light is on even if im not in reverse but in neutral. and the reverse light gets briter as I rev the bike.i clean the carb twice, remove the reverse sensor and check the ohm, reading 0.0 to 0.9. any idea, I need to get this bike going asap. thanks for your time
    • By tperk100
      2014 Honda 420FPA
      I installed a LED bar, but have yet to wire it in. Would like to wire it into light switch circuit for low beams, assuming it will stay on for high beams also. I am an old fart so am looking for an easily accessible place if possible. 

      Other concern is current draw. It takes 2 amps. So wherever it goes, the circuit has got to handle an additional 2 amps.
      Any help will be appreciated.

      Tomn P in Sunny Virginia Beach, Va
  • Similar Tagged Content

    • By LMI
      Was using the quad the other day to shuttle wood from my pickup to my wood pile.  When the job was done I turned off the Quad and heard a bit of a racket from the front end.  When I got down underneath the sound seemed to be coming from the fan housing.  fan was moving in spurts and not quickly... much like a computer case fan that's had it's day.  What I know.
      Temp sensor is ok, as the fan tries to activate fan is getting some voltage as it is attempting to spin.  When I first bought it used I tested the fan direct to battery and it was fine. The fan was working ok even not direct wired as I went on a couple of rides and when stopped and idling the fan did run Seems to be free spinning with my finger read up in the manual and they require me to drop the rad.  now I'm not opposed to that as the rad has some damaged areas I want to try and straighten out.  But if I can get the fan working without, I can leave the rad as it is until next year.
      Fan assembly is about 300 bills, any work arounds or alternatives?  I even thought large computer case brushless fan.  smaller ones are about $7 larger ones better quality probably far below the 300.  They run standard 12v DC.
      Anything I should be doing before dropping the rad... other than check for obstructions even though it seems to spin, and trying to hardwire it to the battery again for a test to see if it acts the same?
    • Guest Fox300exchic
      By Guest Fox300exchic
      The Hop-Up: You may be saying to yourself, “that’s a chick bike,” and you’re right. But honestly, it’s so much more than that. It’s one badass bike. http://www.quadmagazine.com/quad/features/article/0,24942,1587044,00.html
    • By gregj49
      Blows out black smoke when you rev it up how do you adjust the carb?
    • By chuckcnm
      Hi, just picked up a MOTO 4 YFM255 and want to replace the rear brake pads. How do I get to the back. Guessing I need to remove the brake disk, question any easy way to do this?
      Thanks
    • By petersty07
      Thanks to trent at trent signs and graphics for the awesome wrap!!
      [ame]
      [/ame]
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...