-
Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
-
Similar Topics
-
By YamahaBB350
I have a Yamaha Big Bear 350 and the reverse doesn’t work, it shifts from low to high easily but it won’t go back to reverse. I’m new to this stuff, so I’ll take any help. Any ideas?
-
By Hondasher
I picked up a 1997 Yamaha Big Bear 350 2X4 a week or so back in non running condition, apparently they said it needed a new carburetor or a battery, I cleaned the carburetor thoroughly and got it running on idle and without choke now and it shifts into all the gears even into reverse. Aside from making me bounce a little when trying to start out with a bit of throttle the shock suffice to say needs work. Anyways I made a video of it running and would like your opinions on it, as to how it sounds while running. It seems like it has a little whine I'm not sure why that is maybe someone can tell me what it is. Anyways here is the video.
-
By Randel1
Hello,
I have a 2004 Yamaha Bear Tracker in the shop for repair. I have the service manual but it doesn't have all the information I need to fix the problem. I need to know the voltage output of the stator charge coil and pulse or trigger coil at cranking speed. The wiring diagram color code doesn't seem to match and that is compounded by the fact that the wiring harness CDI connector is missing so I have 7 wires that need to be connected to the CDI. I can not find a circuit diagram of the CDI which tells me where the pulse/trigger coil connects or the charge coil connects. The other 3 wires (black ground, orange ignition coil, and r/b ignition kill sw) also need to be connected. The CDI has a single 8 pin connector and has a P/N 4XE-00 F8T19871 -1122 number on it and I believe it to be OEM. However I think the Stator and pulse coil are aftermarket items. I have resistance tested everything and it all seems to be in spec. but I don't want to miss wire anything and cause damage. Any help would be greatly appreciated.
-
By Scott Sirr
I need to figure out how to clean/fix or replace my neutral switch assembly On my 2008 Yamaha big bear 400 as generally the neutral light doesn’t come on when it is in neutral. To get it to come on I have to wiggle the foot shifter and hold it in just the right spot.
I have googled it and can’t find much on the 400’s. I can’t find a service manual online and the parts manual is super vague.
I think it is in the right side engine cover area, but not certain.
Any help would be great. thanks
Scott
-
-
-
-
Similar Tagged Content
-
By weblex
Problem: The ATV starts and runs at idle perfectly. But as soon as I open the throttle, the engine starts to slow down until it stops. On the attached video you can hear the sound of how it works: see video below
Prehistory: there is a Polaris Sportsman 500 1998, which for about 1.5 years stood in repair, including also replacing CDI with one taken from the same ATV. Finally, the vehicles were on wheels, traveled several kilometers and overheated - forgot to fill the antifreeze Came back home in small moves. The next trip started well, but after 10 km there was a feeling of a small drop in power (even as the vehicle got warm completely) but still drives. Next trip - the situation is repeated. The next test of ATV through time and a huge loss of power from the very beginning. The engine sneezes, does not want to go more than 5 mph.
What has been done: the carburetor has been replaced with a new one (inexpensive, $ 40), a new spark plug, a new ignition coil, the engine head has been removed, the piston is in good condition, valves were corrected - but the problem was definitely not in them.
Ignition control unit is suspected. Who faced similar? Please help in solving the problem.
Thanks in advance.
-
-
By alexcross324
Hi all, I try to find this manual in the threads but you have a lot of stock here
Cannot find this particular manual.
I found it for YFM200 but not sure if they are the same.
Thanks if you could help me with that.
Im new here so if I did something wrong, please tell me.
-
By dyyjrr9
I just got a 1991 Yamaha Moto 4 for my son and I am looking for a service repair manual. I know that the timing chain needs replaced.
-
-
Recently Browsing 0 members
No registered users viewing this page.
