Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

quadmaniac

Quad Bike, ATV, Quad, how do you call what we ride? Quad Biking?

Recommended Posts

I was googling something and started to think about the word "QUAD" and how it's used. Is an ATV a QUAD? We used to call it "quad riding" with my friends and not "ATV riding". I think over in the UK they call it "Quad Biking" from what I can tell. So what actually falls under the term "QUAD"? Do side by sides and UTV fall under this and do they fall under UTV as well?

I'm interested to hear what people think about this here at QUADCRAZY.

Share this post


Link to post
Share on other sites


Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • By LTZ-Zach
      So i was riding the other day and my quad randomly shut off. It started back up and ran completely fine for a little while and then it started idling terribly.
      I cleaned the carb and changed all the jets and everything except the float due to the rebuild kit not coming with one and it actually runs worse then it did before.
      It will run and idle decent now but when I give it gas it dies.
      Does anybody know what could be wrong?
      I also changed the spark plug and air filter along with the oil and oil filter.
       
    • By YamahaGrizzly
      Few bears doing water wheelies!
      I fell off the bike and boy is the water cold lol!
       
    • By Jacob Blocker
      I got an ATV from a guy that ran out of time rebuilding an eiger 400. He put a nerma Piston and rings in. I finished it up and it smoked like a train. I took the head off and honed the walls and it looked like the rings where on the walls, but it smokes just as much. I'm confused what's wrong with this thing.
    • By quad man
      Can somebody please tell me if 250x or 250ex nerf bars will fit on 96 300ex, and will 93-98 300ex nerf bars work on my 96 300ex? Thanks
    • By johnwayne
      i have a 2000 suzuki king quad lt-f300f that i picked up as a project bike. it didnt run well when it was parked outside 5 years ago. it cranked after putting fresh gas - but would not run below half throttle, i took apart the carb, cleaned debris, and re-assembled. i suspect that the pilot needle is sheared off - it never protrudes into the throttle body through the pinhole. now to get the bike to ALMOST idle, the throttle idle adjustment knob is all the way up/in. the pilot needle is turned almost all the way in/up (if i understand correct, it should nominally be out 2 1/4 turns or so). and like i said, it will ALMOST idle. floods easily, rides rough.
      wanted to hear from those more experienced than me with suzukis - and im self-taught atv repair, so dont laugh too hard if my verbiage/part names is way off. 
      facing the driver's side of the bike [US] there are three hoses on this side of the carb. without a service manual or way of knowing what was messed up before i got it, i think i have them right: front hose as a vacuum to the petcock, middle hose as vacuum to the fuel pump, rear hose as fuel line from the fuel pump. running the bike in prime position results in flooding even while riding. with all hoses disconnected from the carb, fuel slowly drips from the vacuum line connected to the petcock.
      so just my speculation is that the diaphragm in the petcock is split, and the pilot needle is broke off - causing my inability to not quite idle and the rough ride. this suzuki is hoses and cables everywhere compared to the honda ranchers and yamaha warriors i am used to. I would like to have a plan rather than: replace everything at once.
      is my speculation on the right track, or could something else be at play? say, if the compression was non-existent, would that cause non-idling? i am all ears, look forward to the input.
  • Recently Browsing   0 members

    No registered users viewing this page.


×