Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Steve M.

ATV won’t move except in 4 wheel drive

Recommended Posts

I have a 2009 Artic cat 700 4 Wheeler and it will not move except in 4 wheel drive. Any ideas? 

 

Thank you, Mary

Share this post


Link to post
Share on other sites


What happens when you try in 2wd mode? does it feel like it wants to move or do anything?

Look down at the rear driveshaft, is it turning?

Mike

 

Share this post


Link to post
Share on other sites
16 hours ago, mikeexplorer said:

What happens when you try in 2wd mode? does it feel like it wants to move or do anything?

Look down at the rear driveshaft, is it turning?

Mike

 

Nothing happens, just revs up , like it’s in neutral

Share this post


Link to post
Share on other sites

. It is either  splines have worn out on the  pinion shaft,or possibly  between the  crown  gear  and output to the axles. . When  you  have it in 2WD,  the rear differential is what moves your  machine . The reason  it moves in 4x4 is because the front differential   is pulling the  machine along. You'll  have to  take the  rear drive apart to  find  just what  is gone .

 

  • Like 1

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Tim-ANC
      Had the problem earlier this month. Found the air intake filter (K&N) covered in mud and cleaned it. Took it out this weekend and it worked great until I went on a longer ride.
       
      After it warms up, it bogs down at about 20mph. Engine sputters. No change at full throttle. It runs fine at lower RPM. Once it cools off, I can run it at higher speed for a few minutes then it bogs down. Seems like there is an electronic component that overheats. Check engine display comes on when it happens. Did manage to complete our 34 mile ride though.
       
      Buddy suggested the throttle position sensor. Will dig into the manual later on.
       
       
       
       
       
       
    • By Sheila Hillis
      2008 Polaris Sportsman 800 HO EFI. Has anyone ever tried to move a radiator back to its original spot from a relocated spot.
      I cant seem to get the radiator seated correctly. Any thoughts?
    • By Travis Waller
      We just bought this about 2 weeks ago and the chain keeps popping off. I’ve dealt with 4 wheelers in the past but nothing with this chain setup.



    • By PolarisRich
      I thought I would make a quick "How-to" on setting wheel alignment since I was flipping my tie rod ends and I was going to have to re-align the wheels anyways.
      Here's some of the tools you will need...

      1.) Start with the ATV on a smooth and level surface, like a cement garage floor or driveway.

      2.)Center up (Eyeball It) the handle bars and lock them into place with 2 ratchet straps, one on each side of handle bars. This of course prevents them from moving when your adjusting the tie-rods.

      3.) Place two Jack Stands approximately 2 feet in front of the atv even with the outside edge of the two front wheels.

      4.) Wrap a length of string all the way around the ATV and Jack Stands, Start and end at the rear hitch. Make sure the string is the same height from the ground on all 4 wheels. I like to attach a few elastic bands to both ends of the string before attaching the string to the hitch. This makes it easier to adjust the strings when moving the Jack Stands.

      4.) Break lose the inner and outer tie-rod nuts. NOTE! Make sure you use 2 wrenches, one on the nut and one on the ball joint. Damage can occur by only using one wrench.

      5.) Adjust the string by moving the Jack Stands in or out untill the string just touches both of the side surfaces of the rear tires on each side of the ATV. This will take some time to get it right but it needs to be done!

      Check manufacturers wheel alignment specifications on your specific make and model before you adjust any components.
      For this wheel alignment I'm using the Polaris Specs which seems to be a common setting.
      Polaris - The recommended toe alignment is 1/8″ to 1/4″ toe out. This is a total amount, not per wheel.
      6.) On the front rim, measure the distance from the string to the rim at the front and rear edges of the rim. The rear measurement should be 1/16″ - 1/8″ (.2 to .3 cm) more than the front measurement.


      7.) If an adjustment is necessary, Turn the tie rod itself with a wrench or your hand in small increments. It doesn't take much to move the tire a long way, so go slow. Keep re-checking your measurement's until you have a 1/16″ - 1/8″ differance to the string.

      6.) Once your satisfied that you have the correct "Toe Out" measurements you can tighten up the inner and outter tie-rod nuts on both sides. AGAIN...make sure to use 2 wrenches.
      7.) Now take your ATV for a test drive to test your adjustments. If it still pulls one way or the other, just repeat the above steps to tweek the adjustments again utill your happy.
      The whole process only takes about 15-20 min.
    • Guest foscoe944
      By Guest foscoe944
      Hi, I’m new to the forum. I have a large trailer, about 7500 lbs loaded, that I need to move around in my driveway. I was planning to buy a motorized trailer dolly, but it occurred to me that perhaps and ATV could do it, and then I could not only move the trailer but also have the ATV for the fun of it!
      I’m wondering if anyone knows if an ATV can move a trailer this size? The tongue weight is about 750 lbs, and I’d only be moving it very slowly in a small space on almost level concrete and gravel.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...