Quantcast
Jump to content


Mojave 250 KSF-250 Service Manual 1987-2004


Recommended Posts

  • 8 months later...
  • 2 months later...

I have a 2001 Kawasaki Mojave kfx250 had the valves adjusted and the carburetor clean and adjusted got it back rode it a 1/4 mile and it died the guy who did the work on it said I will be needing a time chain . I think he did something to my atv to get more work out of me . I was looking for a repair manual to try do my own work this time

Link to comment
Share on other sites

What happened when the bike quit? Did it just die, was there a bang ? If that timing chain broke or if the bike jumped timing you could have done a lot more damage then you think.  Valves hit the piston and bend or put holes in pistons etc. You won’t know until you open it up.  if he improperly adjusted the valves that could have caused some problems as well.   If your mechanically capable then you can do the work along with some help from Quadcrazy members and having the manual.  

Two ways to get a manual, one is to have 10 contributions on the forum.  Not just random sh** posts. Or you have a paid membership. 

 

Link to comment
Share on other sites

On 6/16/2019 at 9:56 PM, Ajmboy said:

I just took it to a repair shop and have someone who has a retail and service 9n what they sell what they told the amount that he charge was way to much they would done it for haft what I paid . When it stop running no back fire no noise just die like had no spark or fuel.  I tried to restate it .the kick start would pop my foot back up . I should k ol some time tomorrow what it's going to take to fix it . And see if he actually did something to it  for it to not run again so I would have to take it to him again. .I will be talking with a lawer on it to see what I can do about it cause it ran fine before he touch it it just wouldn't idal

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Mhatayas
      My uncle bought a Baja 250, 2006. Knew there was no spark since the get go. He don't know anything about quads so is getting me to help him try to get it running...
       
      battery is bad so I connected battery charger to it to crank it over , cranks over well , but no spark .... 
      Lights and everything work fine , but with each crank over using the e start switch , the display reads 999 888 777 666 ... Right down to 000 and repeats itself . 
       
      He managed to get a parts bike , I changed over the CDI and the coil and the stator from the parts bike and there was another black box by the voltage regulator I changed over ... I used my multimeter to confirm as much as I could works , it's hard without knowing which wires are which , and I cannot find any diagrams online for this bike ? 
       
      Do you think it could be the Killswitch? There's so many wires coming from there I don't know where to start . Also I should mention it appears the fan on the front of the bike has been taken off (the wires have been cut too ) 
       
      If this bike sparked it would run . The previous owner said he parked it one day and it just wouldn't start after.
    • By Mhatayas
      What should I do about this , bad oil leak where the filter cover bolts on . Can I use some gasket maker 

    • By Uglyside38
      I have a 1988 Quadrunner 250 2wd. My brother in law sold it to my son for $20...had been sitting outside for several years. Got it home and had it running in about 30 mins. Ran it a bit and then went to looking at the carb as it was having trouble idling. Was getting it pretty close, then started losing spark...Also, it wouldn't start up every time...only about 1 in 5 tries. Anyway...now, it has what I can only describe as "intermittent" spark. I can get 1 light spark right when the start button is pressed and sometimes one when it's released...but none while cranking. 🤷‍♂️

      I have replaced the spark plug, ignition coil/wire, and traced wires best I can. I noticed a couple frayed wires at the pickup coil where it enters the case. So, now I have the cover off, stator and pickup coil out and trying to test the coil. I do have about 114 ohms resistance for pickup best I can tell. And I can read minute voltage when I drag a magnet across it. Could it still be bad? Can a bad ignition switch/button cause this? (I did have the switch off to oil the choke cable)...pulling rope makes no difference though...any ideas or help would be greatly appreciated!!! It's the intermittent part that's throwing me off! 

    • By rgeiser
      View File 2003 Polaris Ranger 400-500 service manual
      2003 Polaris Ranger 400-500 service manual
      Submitter rgeiser Submitted 04/18/2024 Category Polaris UTV  
    • By kiriyaaoi
      Hello everyone, I just picked up an 02 LT-F250F the other day and have been in the process of tearing it down to fix some stuff- one of which was the cylinder base gasket leaking like a sieve. Well, I know why that is now, and I also discovered that someone had been in there before. I didn't take pictures, but it looks like it was probably run low on oil at some point, the cam journals and the "bearings" (for lack of a better term) in the head and the valve cover are totally wiped out, very deep grooves.  From what I know it's very difficult to repair aluminum in this way, so I'm trying to figure out where to go next.
       
      1. Have someone grind down the head and valve cover and fit actual bearings in since the aluminum is screwed, and have the cam ground down to match.  I have no idea what this would cost.
      2. Buy a replacement head+cam+valve cover.
       
      #1 I was hoping someone might have some advice on, but #2 seems like it'll (probably) be the more cost effective option.  However I'm running into some difficulty, it seems like the 2001 and 2002 models specifically use a different head part number,  11100-19B10, instead of  11100-19B01 like for all earlier models.  What exactly is the difference between them? There are obviously far more of the earlier heads because it ran for over 10 years.  Are they actually interchangeable? I've also noticed there are heads from the LT250EF that has 4 valve heads but also otherwise look identical.  Would those work as well possibly?  I'd like to not have to drop $500 on machine work or new heads on a $1300 quad that I'm already putting a bunch of new parts on.  Oh, and it has a new piston and the cylinder itself looks pretty good too, as I said someone was in here before me.
       
      Any help or advice would be greatly appreciated. I'll post pics of the carnage tomorrow.
         
       
×
×
  • Create New...