Quantcast
Jump to content


Pulling two quads out of storage


Recommended Posts

I would check compression, oil, spark plug, and connections.  when bikes sit, they tend to rust/corrode/dry rot and the electrical connections usually suffer.  I had an old bike that didnt have spark and just going through the wiring and putting connection grease on the connection brought back spark.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By JohnnyB
      Greetings, 
      Have a 88 LT80 that been sitting for a couple years. Bought a new piston, cylinder and head. Installed these, rolled it over and it quickly locks up.  Took carb apart. It was full of what appears to be 2 cycle oil. Cleaned it, but keeps locking up and 2 cycle oil continues to seap from exhaust port.  When i installed new cylinder, I noticed crankcase was full of oil.  I'm now wondering if that oil is what's getting sucked up into cylinder.  Should there be no oil in crankcase?  If that the case, how is crank and rod lubricated?  Sorry, never worked on a 2 stroke. Thanks!
    • By newguy024
      Just got into ATV riding just last week, never had much money so i couldnt afford to buy anthing, so now at the age of 34 i just bought a 1987 suzuki quadrunner 300 for 500$ took it out a few times and what a rush of excitement to go through that first mudhole haha!
    • By ResQ91
      Hi guys
      My 87 Bear 350 won't start and could use a hand.
      Turn key on and Oil light turns on and then slowly fades out. (I think this is key to this) No start, not even a tick.
      battery and connections good
      A Solenoid post jump turns it over
      Neutral Safety Switch wire attached and seems good
      It has not had a wire/switch on Rear Brake Pedal ever since I had it.
      Any thoughts on some other things to troubleshoot this??
    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • By gatorschevy
      If so, I have covid lol, in the past 3 months I have bought 6.
      04 Suzuki Quad runner 400
      86 Kawasaki bayou 185
      96 Polaris magnum 425
      95 Polaris trail blazer 250
      03 bombardier 175 rally
      92 Yamaha moto 4 350 
×
×
  • Create New...