Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Andrew Serrano

2000 Suzuki King Quad vapor locking problems

Recommended Posts

I have a 2000 Suzuki LTF -300 King Quad. My problem is it will start up great, very fast. It will run fine until it gets hot and I turn it off.  If I let it sit for a bit it will not start until I hold the throttle wide open and crank on the starter for quite some timr, acting has if flooded.....but I checked the spark plug one time this happened, went to change thinking it was flooded but only found a dry Plug????  It starts like if flooded but plug was dry, it takes awhile to start, then to get going I have to really rev it to get it clear and going...Thanks any suggestions would be great, thanks everybody in advance...!!!

Share this post


Link to post
Share on other sites


Have you checked to see if you have spark when this happens ? I know the plug would be wet etc but take a look for shits and giggles when the bike won’t start if spark is there. 

Secondly I would do a compression test before and after the engine is hot as well as take the temperature of the cylinder head. You can do this with an infrared point and shoot thermometer to see how how hot the engine is getting.  

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By ATVNetwork
      Get ready! We're bringing the world‑renowned Nitro Circus to the Glamis dunes for not one, but three exclusive boundary‑breaking shows!   This is a Camp RZR you don't want to miss.   By pre‑registering, you get reserved access to the show and are automatically entered to win one of the Grand Prize Giveaways!   Pre‑registering will get you on the list, but be advised that the first 100 people to check-in at Camp RZR Friday, October 25th will get closest to the action with premium viewing for the Saturday night show.   Learn More   Register Now     RZR Vehicles Shop Accessories Shop Apparel Explore All Off-Road Vehicles                  
    • By goldeneagle
      I have a 2000 warrior thats seems to run fine. But I am having a problem with the gas boiling in the tank. Does anyone else have this problem or can anyone give me suggestions on how to fix this issue? Thanks Bill.
    • By oxidized_black
      these are what i have in my collection ... always looking for more
      1985 - 1990 Suzuki LT230 & LT250 Service Manual
      http://rapidshare.com/files/3408466380/1985%20-%201990%20Suzuki%20LT230%20%26%20LT250%20Service%20Manual.pdf
      1987 - 1998 Suzuki Quad Runner 250 & King Quad 280 Service Manual
      http://rapidshare.com/files/4183862408/1987%20-%201998%20Suzuki%20Quad%20Runner%20250%20King%20Quad%20280%20Service%20Manual.pdf
      1987 - 2006 Suzuki LT80 Service Manual
      http://rapidshare.com/files/2550473580/1987%20-%202006%20Suzuki%20LT%2080%20Service%20Manual.rar
      1987 Suzuki LT500R Quadzilla Service Manual
      http://rapidshare.com/files/4261907986/1987%20Suzuki%20LT%20500R%20Quadzilla%20Manual.rar
      1988 - 1992 Suzuki LT250R Porting Instruction
      http://rapidshare.com/files/2211227601/1988%20-%201992%20Suzuki%20LT%20250R%20Porting%20Instruction.pdf
      1988 - 1992 Suzuki LT250R Quadracer Service Manual
      http://rapidshare.com/files/2017114826/1988%20-%201992%20Suzuki%20LT%20250R%20Quadracer%20Service%20Manual.pdf
      1988 - 1992 Suzuki LT250R Tuning Guide Instruction
      http://rapidshare.com/files/2646189275/1988%20-%201992%20Suzuki%20LT%20250R%20Tuning%20Guide%20Instruction.pdf
      1999 - 2004 Suzuki King Quad 300 Service Manual
      http://rapidshare.com/files/4083575866/1999%20-%202004%20Suzuki%20King%20Quad%20300%20Service%20Manual.PDF
      2002 - 2007 Suzuki 500LTA Service Manual
      http://rapidshare.com/files/117478118/2002%20-%202007%20Suzuki%20500%20LTA%20Service%20Manual.pdf
      2002 - 2009 Suzuki LTF250 Ozark Service Manual
      http://rapidshare.com/files/487503898/2002%20-%202009%20Suzuki%20LTF%20250%20Ozark%20Service%20Manual.pdf
      2003 Suzuki LTZ400 Service Manual
      http://rapidshare.com/files/158558615/2003%20Suzuki%20LTZ%20400%20Service%20Manual.rar
      2006 Suzuki 50LTZ Quad Sport Service Manual
      http://rapidshare.com/files/4135680547/2006%20Suzuki%2050%20LTZ%20Quad%20Sport%20Service%20Manual.pdf
      2004 Suzuki 250LTZ Quad Sport Service Manual
      http://rapidshare.com/files/1048588852/2004%20Suzuki%20250%20LTZ%20Quad%20Sport%20Service%20Manual.pdf
      2005 Suzuki LTA700 King Quad Service Manual
      http://rapidshare.com/files/1790653344/2005%20Suzuki%20LTA%20700%20King%20Quad%20Service%20Manual.pdf
      2007 Suzuki 90LTZ Quad Sport Service Manual
      http://rapidshare.com/files/4042730335/2007%20Suzuki%2090%20LTZ%20Quad%20Sport%20Service%20Manual.pdf
      2008 Suzuki 400FLTF King Quad Service Manual
      http://rapidshare.com/files/3004786025/2008%20Suzuki%20400F%20LTF%20King%20Quad%20Service%20Manual.pdf
      2008 Suzuki 750 King Quad Service Manual
      http://rapidshare.com/files/630050962/2008%20Suzuki%20750%20King%20Quad%20Service%20Manual.pdf
      2009 Suzuki 400LTZ Quad Sport Service Manual
      http://rapidshare.com/files/3513183033/2009%20Suzuki%20400%20LTZ%20Quad%20Sport%20Service%20Manual.pdf
       
      ALSO CHECK SUZUKI ATV SERVICE MANUAL DOWNLOADS
    • By Dra O
      posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
      -fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
      -along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
      -I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
      -can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
      -it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
      -I THINK it has a mikuni model x carb - diaphragm is ID 26mm  OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
      -last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
      -any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
    • By lanow
      Hi Everyone,
      I am new to this forum and hope that someone out there can help me, I have an early Suzuki King Quad 300 (280cc) which starts intstantly every time but at about half revs or there abouts it starts spluttering and will not rev any higher, this fault is present whether choke is applied or not, some one suggested that silencer maybe be clogged so removed baffle but no improvement have removed carb and stripped 3 times but still no joy.
      Any ideas would be most welcome.
      Cheers Rob
  • Similar Tagged Content

    • By Dra O
      posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
      -fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
      -along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
      -I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
      -can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
      -it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
      -I THINK it has a mikuni model x carb - diaphragm is ID 26mm  OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
      -last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
      -any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
    • By LMI
      I wanted to share an experience and a fix.
      Headed out was following a pole line, was looking for a cross track that may take me to this speckle trout looking spot on a creek.  All paths and semi paths... failed.  Second objective was to reach a speckle trout lake that has been recently stocked... followed 1 trail to dead end, followed second trail to dead end.... while investigating options on foot and the quad idling it died.
       
      It wouldn't start.  eventually it did... and when it did … it was essentially a pinned idle.  activating the throttle did seem to speed it up but it wouldn't knock out of the racing idle.  couldn't put it in gear at that idle speed.  got towed out.
      when I first got the quad, I ran it off a trail and buried it pretty good in the soft snow... eventually winched out.  It wouldn't start.  eventually did and it was fast idling.  not as fast as this last time. but still fast.  it eventually seemed to settle and I got it in gear and by the time I was back to the truck was acting ok.  chalked it up to the bike being at a bad angle in the snow.
      My investigation last year lead to the throttle position sensor TPS.  how to jumper the diag block to see the sensor position on the display,.  I focused on this nearly sure it was a detuned sensor or broken sensor again this time.
       
      I tore down the front plastic and stuck my head into the TPS area to see what I could see.  What I found was that the throttle body assembly had actually come out of the mounting area (not sure what it is called).  the ring clamp was loose I could move it easily.  Hopeful, I tore down the air intake assembly above it (air filter...etc) removed a sensor clip and a hose.
      I backed off the clamp some more and was able to reseat the throttle body assembly.  put some blue lock tite on the clamp screw.  When I was cleaning off the air intake assembly to ensure I dropped nothing down the intake, I noticed the underside of the air intake "box" also had a clamp.  this screw was completely missing.
      I went to the hardware store, bought a metric replacement (brought clamp with me), seated the assembly, settled the clamp blue lock tite that as well... 
       
      quad fired right up, idled normal, idled up without hesitation and dropped right back off.  Cost of solution $3.87 CND for a pack of 5 metric screws.  moral of my story was don't assume an idle issue is a throttle position sensor problem... there are a number of other factors including air pressure, which I believe was my issue.
       
       
       
    • By Andrzej Polak
      hi
      Where installing a winch to KINGQUAD ltf300?? someone have any pic?
    • By Gus Drake
      I'm helping the widowed neighbor out to do some oil changes on her quads. Any recommendations on what type of oil to run in these machines?
    • By Mudrecon
      as the topic says I'm interested in brands of mufflers ur using. I want a quiet (drive up on moose quiet) but performance type. Whos got what? Mines seen better days
       
       
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...