Quantcast
Jump to content

Recommended Posts

Posted

I have a 2000 Polaris Xplorer with the 250 two stroke motor

It does not want to start with the electric start, the motor cranks fast, the battery is good, and there is good spark when cranking. The engine starts perfect when using the pull cord, it even starts if I pull the cord slowly and starts with one pull. The engine idles smoothly once started. My wife says she needs the electric start to work.

 

Posted

You'll  have to  trace out the wiring on it . There  is a safety switch  or relay not working in the ignition  circuit.  I  would guess  most likely  a relay or possible broken wire  since  it  turns over  on the starter.  Usually  when safety  switches  fail  the  starter  also will  not  spin.  It is not  getting  power to run  when the  start  relay is energized  so  start there  after  checking for an  obvious broken wire.

Posted

I put a OTC spark tester on the spark plug lead and had good blue spark, then I used my adjustable spark tester and found the electric start would produce a max of 1/4 spark jump, the pull cord would max at 3/8 jump. Then I installed a new spark plug non resister type and lowered the gap to 0.020 and it still would not run with electric start but still starts fine with pull cord.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Thekevinjb
      Can anyone provide information on connecting a hitch to a Polaris. Anyone know where they sell small trailers for my quad. 
      thanks
    • By RGS
      1989 Moto 4 YFM350ERW intermittent spark.
      Quad has set for about 7 years and was running when parked.  When I replaced the battery and attempted to start it had no spark. 
       
      What I have done.  Followed troubleshooting in the manual. 
      1.       Coil failed the resistance check so I replaced it.  Still no spark.
      2.       I performed resistance checks on the stator and they all pass.
      3.       Found a bad rear brake stop switch and unplugged it and connected the wires in order to disable.  Now I have intermittent spark.  I believe that the issue is with either the stator or CDI and not sure which.
      1989 seems to be a transition year for electrical.  I can get new aftermarket CDI units for 87-88 and 90-94.  I cannot get ones for a 89.  I can get new stators for 87-89 and 90-95.  Looking at the schematics the wiring on my moto is closer to the 90 ones on the ATV side of the CDI and closer to the 87-88 on the stator side of the CDI.  Looking at part supply sources the stator housing is the same part # for all the years and looking at some of the stators on Amazon that have the dimensions on them both of the stators are the same size.
      What I am thinking of doing is to replace the stator and CDI with a 90-95 one as these parts are all readily available.   Does anyone know if this has been tried before and if there are any issues with doing this.  
       As a side note I also have a 1993 Moto 4 YFM350ER that has been sitting longer but it is located about 400 miles from me at this time.  By doing this change in addition to being able to get parts I will also have 2 ATV’s that are the same electrically. 
    • By BuckBilly
      Good morning to all !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
      Let's see if we can make this a daily event.
    • By Atomusthenes
      This topic is being opened to discuss the feasibility of forced induction on small engines.
    • By Tim Keiper
      1st problem, Does anyone know where I can find a stock carb for my Timberwolf, I have tried two different aftermarket carbs and they both suck. The machine runs great until it gets good and warm, then it keeps stalling unless I feather the throttle. it will even stall while I'm trying to go from 1st to reverse or vise versa. I took it to a buddy of mine who is a bike mechanic for years, and he told me try to find a factory carb. When I look online from dealers it says "NOT AVAILABLE" anyone have any suggestions ?
       
      2nd, The small tab on the rear axle for towing is to short for even pulling my small yard trailer, I can't even turn a little bit and hit hits. I tried making an extension which worked great as far as length, but it bends the tab and then the extension drags the ground. I have an idea of what to do to fix it, but wanted to see if anyone else has had this problem and see how you solved it.
×
×
  • Create New...