Quantcast
Jump to content


2002 Suzuki Vinson 500 Stopped Running

Amboyjim

By Amboyjim
in Suzuki ATV Forum

 Share

Recommended Posts

Amboyjim Newbie

Amboyjim

Posted
Posted

Having serious problems with quad it completely stopped running on me took carb off and tore apart cleaned everything put back on and it started idled but when driving it had no power at all so took carb back off and noticed their was a puddle of gas and oil in the bottom of the air filter box and also their was gas in the vacuum line HELP

Link to comment
Share on other sites
Frank Angerano Grand Master

Frank Angerano

Posted
Posted

Hey @Amboyjim welcome to Quadcrazy! 
Check the diaphragm on the fuel pump. If the diaphragm is bad and gets a hole in it the fuel gets sucked into the carburetor via the vacuum line and floods the engine and winds up getting kicked back into the air box.   
 

Also when you set the air fuel screw after the carburetor rebuild did you set it properly?  

  • Like 1
Link to comment
Share on other sites
JacobSlabach Mentor

JacobSlabach

Posted
Posted

yea theres definitely a carb issue going on.  does your quad start sputtering once it gets hot and trying to cut out on you?  just wondering because i had a yamaha warrior that was collecting gas and oil in the airbox and it would run awesome until it warmed up and then it would quit

and that bike didnt have a fuel pump- just gravity fed

  • Like 1
Link to comment
Share on other sites
JacobSlabach Mentor

JacobSlabach

Posted
Posted
On 4/3/2020 at 6:52 AM, Frank Angerano said:

It could be a bad rectifier also once it gets warmed up.  Very possible.   

yea i didnt think about that..  i was pretty sure with my bike it was due to me rebuilding it with a used piston and rings off another atv that i rebuilt lol.  but it could be the case with your atv

  • Like 1
Link to comment
Share on other sites
  • Ajmboy changed the title to 2002 Suzuki Vinson 500 Stopped Running

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • Clydaho
      2022 Hisun Sector 550 Gas gauge stopped working
      By Clydaho
      2022 Sector 550, 414 miles on it and the gas gauge reads empty.  I topped off the gas and it didn't change.
      There is no fuse that I could find.  No access at the gauge cluster.
      Wiring on the top of the tank looks good, properly connected.
      Could the sending unit in the tank be stuck or broken?
      Has anybody removed the tank lid?  Any tricks?  
      Any other ideas?
      Thanks for any help,
      Clyde
    • hardcastle
      1993 Suzuki King Quad 300 bucks and farts like crazy
      By hardcastle
      My friends KQ 300 starts fine and runs, as soon as you put it in gear and try to accelerate its bucks and farts like crazy, not moving... I cleaned carb and it worked good for 1 day... now back to same problem.... could it be such as a bent valve????
    • ResQ91
      Help with 1987 Yamaha Big Bear YFM350FWT Carb
      By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • Its-always-something
      98 arctic cat 300 2x4 hi rev choke when started
      By Its-always-something
      Have a 1998 AC 300 2x4, Just installed a new carburetor. Engine starts easy but the choke RPMs are very hi and take along time (5-10 mins when cold out). After engine has warmed up choke releases and it idles and runs fine., It does no have an electric choke. The choke lever is never used and it seems like an auto choke? Long story short, how can I lower the choke rpm levels?
       
      Also, carb came with a spare145 jet, not 100% sure what is installed. Could this impact choke RPMs?
       
       
      Any help and information greatly appreciated.
    • Tuzz
      1990 Suzuki King Quad 300cc Kicks and bucks when accelerating unless ignition switch is in LIGHT position.
      By Tuzz
      Bucking started about a month ago and works ok after 1/2 hour warmup.  Today while working on it i discovered that if i put the ignition switch in LIGHT position it runs fine right from the start.
      I'm stumped!  Any idea why this could be?  

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...