Quantcast
Jump to content

Yamaha Moto 4 CDi Box

Brewster

By Brewster
in Yamaha ATV Forum

 Share

Recommended Posts

Brewster Rookie

Brewster

Posted
Posted

Being confined to the farm with the corona virus pandemic, I have started working on long abandoned projects.  I have a 95 Yamaha Moto 4 350 and the CDI box went bad (I think).  Finally broke down and spent the money for a new one.  It had the same part number as the old one, but the old box as 2 extra wires on the pig tail and not all the wire colors with the new box match the old box, so I'm not sure how to hook it up.  Have searched the internet on and off for some time but can't seem to find anyone who can help.  Does anyone out there know enough that they would try to help me?

06kfx440 Proficient

06kfx440

Posted
Posted

Does the colors match up. They may be in the wrong spot on the plug


Sent from my iPhone using Tapatalk

Does the colors match up. They may be in the wrong spot on the plug


Sent from my iPhone using Tapatalk

You may have to switch plugs.


Sent from my iPhone using Tapatalk
MarkinAR Experienced

MarkinAR

Posted
Posted

I'm not sure if the same CDI was used the entire run between 87 and 95, but I know the early Moto 4 CDI's were actually the CDI used on the last year of the 3 wheeler.  It was unlike the rest of the Yamaha quad line and is quite an oddity.

Do the 2 extra wires connect to wires in the harness?  Or do they connect to blank spots on the plug?

06kfx440 Proficient

06kfx440

Posted
Posted

If everything else matches. Then move those off to the side. What I would do is remove the pins out of the plug. This can be done with a pick. Something small enough to get the tab to move to pull it out. Then connect said matching colors. There should be 2 wires of the same color left. Do you know what machine the new one came out of? If so get that diagram and your diagram and match them up


Sent from my iPhone using Tapatalk

I had to do this with my “ death trap kx 250”


Sent from my iPhone using Tapatalk

Frank Angerano Grand Master

Frank Angerano

Posted
Posted

Personally if i broke down and spent the money on a cdi it damn well better be the right one! Plug and play...... what year is your machine and what did you buy? Oem or aftermarket? Id it possible they sent you or you ordered the wrong part? 
 

The last thing one would want to do is start chopping up a harness after spending money on a cdi.  
 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • RGS
      1989 Moto 4 YFM350ERW intermittent spark.
      By RGS
      1989 Moto 4 YFM350ERW intermittent spark.
      Quad has set for about 7 years and was running when parked.  When I replaced the battery and attempted to start it had no spark. 
       
      What I have done.  Followed troubleshooting in the manual. 
      1.       Coil failed the resistance check so I replaced it.  Still no spark.
      2.       I performed resistance checks on the stator and they all pass.
      3.       Found a bad rear brake stop switch and unplugged it and connected the wires in order to disable.  Now I have intermittent spark.  I believe that the issue is with either the stator or CDI and not sure which.
      1989 seems to be a transition year for electrical.  I can get new aftermarket CDI units for 87-88 and 90-94.  I cannot get ones for a 89.  I can get new stators for 87-89 and 90-95.  Looking at the schematics the wiring on my moto is closer to the 90 ones on the ATV side of the CDI and closer to the 87-88 on the stator side of the CDI.  Looking at part supply sources the stator housing is the same part # for all the years and looking at some of the stators on Amazon that have the dimensions on them both of the stators are the same size.
      What I am thinking of doing is to replace the stator and CDI with a 90-95 one as these parts are all readily available.   Does anyone know if this has been tried before and if there are any issues with doing this.  
       As a side note I also have a 1993 Moto 4 YFM350ER that has been sitting longer but it is located about 400 miles from me at this time.  By doing this change in addition to being able to get parts I will also have 2 ATV’s that are the same electrically. 
    • Suzukiquad
      New member / quad lover
      By Suzukiquad
      Hi, I have been around everything with a motor since I was little, and finally purchased more to get my husband, and kids involved. I have 4 quads I will be searching around for information on. I have two 2002 Suzuki LT80K quads, a 1997 Yamaha Timberwolf 250, and a 1996 Kawasaki Bayou 220. I have had different ones throughout the years, and plan on buying another Yamaha Banshee. I plan on trying to learn more about all of them, so I can customize some of them. I know nothing about them besides how to race them, my dad always took care of the rest, but figured it was time for me to learn. 
    • Kaz
      1999 Yamaha Big Bear 350 4x4 no spark
      By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • KSIM
      2018 CF-MOTO Z-Force CF1000US-2 Service Manual
      By KSIM
      View File 2018 CF-MOTO Z-Force CF1000US-2 service manual
      CF-MOTO Z-Force (CF1000US-2) (2018) service manual
      Submitter KSIM Submitted 03/19/2025 Category Other Brands UTV  
    • P_syko
      Need help! 1987 Yamaha Moto 4 350
      By P_syko
      I’m brand new to 4 wheelers and just bought a 1987 Yamaha Moto 4 350. It has good compression and fuel, but no spark. I’ve looked high and low trying to find how to test all the components of the ignition system, but can’t find anything. This has a new CDI box on it, but I suspect it might be the stator. How do I test the stator on this? Any help would be greatly appreciated! 

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...