Quantcast
Jump to content


2000 Polaris Magnum compression issue


Recommended Posts

Came here for help, If it’s in the wrong place I’ll move. I’ve got a 2000 model Polaris Magnum 500 that runs strong as can be for about 25 mins until warm, then sputters and loses power. Took it to a shop and they say it’s low compression and they will have to swap the entire engine. Seems a bit much and costs more than the entire bike. Was wondering if anyone has seen this and what the fix was. When I hear compression I think of gaskets, not an entire engine. Seems like if it was that bad it wouldn’t have power cold. I’m at a loss. Any help is appreciated greatly. 

Link to comment
Share on other sites

Welcome to Quadcrazy @Tyler Reed ! As @Ajmboy said you came to the right place! Any repair shop that recommends you need to swap out the engine based on your symptoms is a shop I would never return to my friend!  So what i would do is start With the basic testing first.  

Does this happen during all riding or in damp/wet conditions? 

Go get yourself a cheap compression test kit from Amazon or anyplace.  Take a compression reading while its ice cold and then a reading after it starts to act up.   Compare your readings and see whats what.   
Secondly I would locate the regulator/rectifier and see if its over heating after the atv acts up? It's cheap enough to replace if suspected.    
Im not sure if your machine is water cooled  but is the cooling fan coming on? Could be getting super hot and causing the problem. Don't trust temperature lights etc. Visual verification of the fan running is key. 

Next I would check your air box and make sure everything is ok inside, filter good, no overload of gas inside the box or water? 

Lastly is making sure your fuel is flowing properly to the engine weather it be some sh** at the bottom of the tank or maybe a condition where this happens when you get to a certain fuel level in the tank ? And we have been talking about vapor lock by maybe a bad gas cap? 
 

Start with this and see how you make out.  
 

 

  • Like 1
Link to comment
Share on other sites

If it runs strong for 25 minutes, even if it's blowing smoke, I don't see engine replacement needed.  Even if rings are completely shot there's rarely any variation between perceived power cold and hot.  I'm leaning more towards what Frank mentioned above; fuel starvation or some component getting hot like coil, regulator, etc.  I'm willing to bet it's a pretty simple answer if you can do some basic troubleshooting.

  • Like 1
Link to comment
Share on other sites

  • 8 months later...
  • 3 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Spritee1
      having an issue with the unit when running under a load up a hill or in high gear, seems like the belt is slipping, there is a clapping sound coming from the primary clutch like it releases and snaps back in. i don't think I should have a noise like that. this is a friends unit and he has already replaced the primary twice with the same result.
      not sure where to look next
    • By Johnfj44
      The stock driver seat cushion is separated at a seam. I took the seat apart and found that the material has torn and cannot be re-stiched. I'm trying to find a replacement seat. Any suggestions? Hoping for a used seat but couldn't find one on Ebay.
    • By Slitzer
      Hi,
      Got a Big Boss produced 2016 YM 2017 that gives DTC 520 285 2 (random)
      What I understand is correlation code for brakesensors, very little information in workshop manual.
      Removed front plastic to discover that no connector was mounted on the brake pressure switch!?
      The only "brake" information seems to come from the micro switch at the brake lever.
      Does anyone know if Polaris does anything special on the 6x6 or had this issue?
    • By mkibbe
      My 2014 750 king quad stalls sometimes when I touch or turn the handlebars,the problem has gotten worse,my machine has 475 miles and is only trail ridden,I have a new factory battery and i have 14.2 volts when the quad is running and 13.3 on the battery when not running,also using a multimeter there is no change in volts when turning the bars until it does stall,If I pull the 40 amp power steering fuse it will not stall.......I've been told its the ECU,Hate to buy one if thats not the problem,but its kinda leaning towards that,,,,,need some opinions.

    • By bighoss
      i got my son new outlaw 50 a few weeks ago and we went rideing yesterday and while we were riding it died and it took me like 10 min to get started back and it died agen when we got close to truck so i pulled it back took the plug out it looked like it was drop in a bucket of gas took the air filter out and the ait box was full of gas also got home it started rite up today i started it it starter up but was blowing what look like water out of the exholst let it idel for a lil bit did not die but as soon as hit the gas and let off it will die what does that sound like i thnk i going to take it back to dealer and tell them to fix it as it is under warrenty but would like to know what it could be first
×
×
  • Create New...