-
Do you own an ATV or UTV? Join our Forum!
Join QUADCRAZY ATV Forum today for FREE! We keep these forums clean and user friendly. All first posters will have to wait to have their content reviewed and approved. Once your first post is approved, you will no longer need to got through an approval process. To gain immediate approval and a NO ADS experience, consider subsribing to our Premium Membership.
-
Similar Topics
-
By mga
I just brought home a used 2005 Yamaha Big Bear 400 4x4. It needs front wheel bearings, and a new choke cable. I think i can handle those two items. However, when i went to look at it, it ran good, shifted good, brakes all workds great, but at home when i started it, it would idle nice, but when i gave it gas it seemed like it was flooding out and would die. If i just gave it a little throttle it built up RPMs but any more throttle it began dying out again.
any suggestions why it's doing that?
I'm looking for a service manual, but forum rules say i have to make 10 posts..lol
oops...i just realized i posted in the wrong section of the forum!!
-
By Parham
This quad was a hot mess two weeks ago when I got it. I've been tinkering on it and have it running pretty good. It didn't have a pull start. I just got one and installed it today. Here's a little video of my first try at using it. Hope it's worthy of a "onya" from Mech! 🙂
IMG_3274_Trim.mp4 -
By Parham
I just bought this a couple of weeks ago. The oil sightglass was FULL. When I opened the fill plug, oil/gasoline LITERALLY gushed out and flowed for several seconds...FROM THE FILL PLUG! I drained it, changed the filter (no metal bits), and refilled with new oil. Opened up the carb and cleaned the float needle. Blew into the fuel inlet while manipulating the float and it seems to work. Buttoned everything back up and it runs good. Now my question...was the fuel getting into the engine because of a stuck float needle or is there something else wrong?
-
By Am2007
Hi everyone,
Outlander 2006 400 XT i have replace the startor cover and right after i did that the oil light is on and not turn off, i check the wires and checked the oil level, everything seem to be normal quad is starting without any problem and rev just fine. i did not want to ride it since im not sure if it is faulty sensor or not so just be safe i did not let it run more the a minute or so.
I have read in the owner manual that i need to clean the oil strainer every 200hr unfortunately i never did that, my service manual that i have does not even indicate of such a thing. so i did some search around and it seem like canam split the manual into 3 parts
owner manual
service manual
engine manual
I have the first 2 but i can not find the last one, part number 219100232. If someone can guide me where do i find the oil strainer so i can clean it i will appreciate it. im going to do an oil pressure test tomorrow to check how many PSI i have, just to make sure.
Thanks
-
By Ulfthednar
Just a quick test video while I'm learning to use my gopro (really, $250 discount I couldn't pass it up).
This is from my side drive to the top of the property.
The Dog loves the runs.
No snowflakes were injured in the production of this video.
https://youtu.be/tKjBFuHCkM0
-
-
Similar Tagged Content
-
- 3 replies
- 404 views
-
- 3 replies
- 409 views
-
- 3 replies
- 620 views
-
- 0 replies
- 623 views
-
- 0 replies
- 913 views
-
-
-
Gallery Images
-
3 -
0By hotrider,
-
1
-
2
-
5By TheBatman28,
-
0
-
0
-
5
-
5
-
2
-
3
-
1
-
2By oxidized_black,
-
5By justforfun02,
-
0
-
2
-
0
-
4
-
0
-
3
-
-
-
Recently Browsing 0 members
- No registered users viewing this page.
.jpg.dae6846dd3f898104f86ce4b067428a0.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.