Quantcast
Jump to content

Recommended Posts

Posted

I have been working on this quad for a buddy. When he brought it over it didnt run. Well removed the carb and cleaned well...then changed the o-rings and changed the spark plug. After all that i put it back together and hit the starter. It started up after cranking a while and ran for about 5 min. and then bogged and died. And wouldnt restart.I cranked for a while and it kinda speeds up like it gonna start but just wont. I let it set for awhile and bam it started agian..and then the same thing, after about 5 min. of running it just boggs and dies.

I did a compression check and got 125, so im ok there.

But i did notice a lot of oil on top of head. I cleaned it off and when i ran it till it died i noticed that all that oil was back. Could i have a blown head gasket?

Posted

IF you did a Compression Check and Got 125 then you dont have a Blown Gasket...It would have leaked Down...Im not Familiar with the Quads....But does it have a Vented Gas Cap???? Have you tried to run it without the Cap on??? What happens is Pressure builds up and Stops the Fuel from Flowing.....is the LT80 2 Stroke???

Posted

yes its a 2-stroke, and the gas cap might be a good idea cause the fuel petcock is ran from the vacuum of the carb. But i still dont know where all the oil is comming from.

  • 1 year later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By HoldenBoy
      Hi all,
      Looking for some help on a starter/bendix issue. Can Am outlander 450 2017. While cranking to start, the starter spins and engages into the ring gear. After a few seconds the bendix retracts while still spinning and there is no damaged teeth on the drive pulley.
    • By TomJulio
      My 1992 TRX00 recently stopped firing.  I understand this is a common problem. I have ordered an aftermarket CDI unit.    TJ
    • By crankin
      I have a 1997 Yamaha Big Bear 350 4x4. It used to start right up. Then all of a sudden it wouldn't crank. I have a schematic for it so I started tracing the problem. I had no power at the starter solenoid. According to the schematic the power comes from the neutral switch and through the starter circuit cut out relay. I cannot locate the cut out relay on this machine.. If I apply power to the relay it will crank with the start button.
      The neutral switch is hard to get to with all the brackets on this thing. I did find out from all my research that if I apply the rear brake lever it will start.
      Does anybody know if the cut out relay exists and where it might be found?
    • Guest
      By Guest
      Hey all, new to the forum! I just bought a 1998 Kawasaki bayou 300, 4x4 not running. Initially I found no spark. Ended up playing with the plug wire (made sure plug top and wiring was touching) and got spark yesterday and the quad fired up off ether. Come to work on it today and now no spark again. Before I got spark and now today if I touch the plug after cranking I get shocked, and it will spark after I release the starter button. I was jumping the quad with a freshly charged car battery that has 12v while cranking. Cleaned out the kill switch and ignition button. All looks good. Purchased new plugs. They're are a lot of wires cut/ disconnected. But shouldn't matter if I got spark without them connected... 
    • By joezee13
      After turning off engine in neutral  starter wont engage If I rock unit back and forth it engages Getting progressive worse.
×
×
  • Create New...