Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Rodolfo205

Stiolen Yamaha Raptor 700

Recommended Posts

Hi guy's

I have a Raptor 700 2007 and they stole it from me.

i found it back but with out frame and Fenders, can some one help me where I can buy a Compleet frame and a compleet Fender kit.

Please reply on this msg or email me

rodolfo_d[email protected]

Thanks

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Venom
      Hi All,
      I did a total restoration on a 2003 Yamaha Raptor 80. Rebuilt the engine and tranny.. Started it up today and it runs great. Took it for a ride and the transmission worked perfectly. Adjusted the carb a little more and went for another ride. It ran awesome, pulled into the workshop shifted into neutral ( Neutral light came on) and shut off the bike. went to roll it and noticed she would not roll. Turned on the key and neutral light was on... After some troubleshooting I found that she is in first gear with the neutral light on and will not shift into neutral... It seems to up shift fine into 2nd and 3rd and then back down to 1st. I am hoping somebody can shed some light on what is happening... Thanks for any help...

    • By Venom
      Hi, All

      I started this project a while ago.. I have decided to make one thread I can continuously update..

      So , here we go. I got this Raptor 80 in really bad condition.. Rear end frozen, Engine toast, tires dry rotted, tons of rust..etc.. They admitted they beat on it very hard.

      Since they do not make these with a drive shaft anymore I decided to restore it from top to bottom..

      These are photos of when I got it home.

      Next up, the tear down..



      First, I needed to tear it down and determine if the rear end was still good... As we all know... That is where it would be cost prohibitive to restore if it is trashed..

      Got it completely stripped down and I lucked out... The rear Drum brake was caked solid inside with dried mud. That was causing the rear end to lock up. Took off the rear brakes and the rear end spun perfectly smooth.

      Once I got it all stripped apart I needed to take the finish off all the parts. I am going to be powder coating the frame and many parts.. Once the finish is off each part it will need to be sandblasted to white metal .. The guy I use for powder coating gives me a hefty discount if I bring the parts to him ready to go.

      You could just sand blast, but that would take a long time to get the finish off. First I used Aircraft Paint Remover.. That stuff is pretty toxic Goggles and Resperator are required. That quickly gets you down to the metal... Then you can sand blast to white metal pretty quickly...


      I had another thread I had started about a problem with the tear down... It has some great info .... here is the link... It is about removing the frame bushings. ....
       
      https://www.quadcrazy.com/atvforum/topic/14209-raptor-80-frame-bushings/?tab=comments#comment-104702
    • By bradley nelson
      Im cool with the police in my area so i can ride on public roads.
    • By Bob Hill
      I need a motor but i really dont hsve lots of cash and im on the kenai peninsula. Up here in Alaska i really need help
    • By Scott Sirr
      View File 2007-2012 Yamaha Big Bear 400 4x4 Service Manual
      2007-2012 Yamaha big bear 400 4x4 irs service manual
      YFM40FBW
      Submitter Scott Sirr Submitted 12/22/2019 Category Yamaha ATV  
  • Similar Tagged Content

    • By mikeexplorer
      Wiring diagram for 2007 Arctic Cat 700 EFI 4x4
       
       
    • By Admin
      View File 2007 Arctic Cat 700 EFI 4x4 Wiring Diagram
      2007 Arctic Cat 700 EFI 4x4 Wiring Diagram
      Submitter Admin Submitted 06/29/2019 Category Arctic Cat ATV  
    • By Admin
      2007 Arctic Cat 700 EFI 4x4 Wiring Diagram
    • By x
      It's time to replace the shocks and struts.  Looking for some stiffer springs than the OEM as I use this for farm work and I put heavy loads on the rear and haul small trailers frequently.  I've seen a couple aftermarket offerings that say they're 10% or so heavier duty.  Any other options for something a little stronger / stiffer?  Thanks.
    • By LMI
      The saga of the fan continues.
      The Pin attempt in the fan shaft failed.  I then moved on to trying to weld the fan hub to the fan shaft.  I took it for a run the weld broke.  Now it was truly F'ed.  To recap the dealer price, they want $400 + CND for a replacement fan assembly.
      I searched all sorts of after market places and no one carried one.  Ebay had some used ones but they were $120 USD + Conversion rate for something as old as what I have.  I went to Amazon and eventually settled on this.
       
      amazon link
       
      What I found... and was amazed... was that the fan mounted to the Suzuki fan assembly bracket.  I was prepared to manufacture my own mount conversions...  It also came with "Harpoon mounts" (nylon zip tie like things that go straight through the rad.   Anyways it mounted to the original bracket. It fit perfectly.  Cut the electrical plug off replaced it with the Suzuki... all good.  Let the quad heat up, thermo coupler kicked in the fan circuit, polarity was right... all was good....  Fan is under the circuit fuse rating.  
       
      so I finally have a solid fan solution.  $34 CND vs $400+ CND
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...