Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
By Dra O
posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
-fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
-along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
-I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
-can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
-it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
-I THINK it has a mikuni model x carb - diaphragm is ID 26mm OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
-last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
-any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
By Scott Sirr
I need to figure out how to clean/fix or replace my neutral switch assembly On my 2008 Yamaha big bear 400 as generally the neutral light doesn’t come on when it is in neutral. To get it to come on I have to wiggle the foot shifter and hold it in just the right spot.
I have googled it and can’t find much on the 400’s. I can’t find a service manual online and the parts manual is super vague.
I think it is in the right side engine cover area, but not certain.
Any help would be great. thanks
Hi guys I'm in the market for a new ATV. I narrowed my choices down to King quad 750 Grizzly 700 and Rubicon 520, I own a 2006 500 Rubicon right now and I like the reliability and power for plowing. However it is not a capable ATV. When quading with other guys it falls short with ride quality and ground clearance. I also have a 500 King Quad 2015 which I like and will keep it for my wife. It is very strong and reliable also. However my plan is to sell my Honda Rubicon and replace it with a 2020 of one of the these mentioned above. Can anyone give me their take on one or all of these machines and why you picked what you picked?
So my Yamaha grizzly 700 wasn't going into reverse for some reason but Jon and George figured it out on what to do to fix that problem for me. Jon Talks about how he was able to fix that problem my Yamaha Grizzly was having with the reverse.
On a side note we are so close to 1k subs! hell ya!
Similar Tagged Content
Just thought I'd start a new thread for newbies to the site!
If you're new here, tell us who you are, where you're from and what you ride!!!
Lets get to know each other a little better shall we?
I'm not new to the site, obviously, but...
I'm Kristin from Denver!!! I ride a 2008 Yamaha Rhino. She's my muddy baby!!!!!! Several aftermarket parts on her. She's good to me! We try and ride every weekend. This weekend we're off to MOAB! :woot:
hello riders,new guy in the house.i am a owner operator of a custom metal polishing shop,located in southeast indiana.i live to polish and love to ride!!
If you have any nasty looking parts that you might want to refinish hit me up,carbs,rims,trees,lower legs,swingarms,cylinders,heads,covers well you get the idea.
For more info pm or email me i will hook you up!!!
Recently Browsing 0 members
No registered users viewing this page.