Quantcast
Jump to content

Recommended Posts

Posted

I rode pretty hard 2 different times while I was in Indiana. I could not get to a power washer before jumping back on the highway. Im back in Atlanta & my Grizzly is still sitting in the garage, as filthy as the day I drove it. Will it be ok if I dont have time to spray it off until later next week?

Posted

I've kept my quads muddey for weeks at a time, especially in the winter when the stuff freezes on there. I've had to soak it down with hot water to get the mud off..on occassion. Should be fine though.

Posted (edited)

Storing a machine dirty for a while wont really do any harm. Never cleaning it is different. Dirt is abrasive, so any moving parts will wear prematurely if they are always dirty. I am not real big on washing my machines to a shine, in fact, they always look dirty. However, I do like to give them a good hosing after riding to knock most of the dirt off the machine and then I lube everything.

Edited by DirtDemon

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By HoldenBoy
      Hi all,
      Looking for some help on a starter/bendix issue. Can Am outlander 450 2017. While cranking to start, the starter spins and engages into the ring gear. After a few seconds the bendix retracts while still spinning and there is no damaged teeth on the drive pulley.
    • By Adamb2025
      I have a 1990 Honda fourtrax 300 2x4
      I rode the other day for 30-45 min. Switched it off and now it is completely dead..
      battery is fully charged, fuses are good . WILL NOT TURN OVER ,
      headlights won't turn on , No neutral, reverse or oil temp lights . Electrically it is completely dead !!! I replaced the key switch and CDI box , STILL NOTHING.
      I bypassed the neutral safety switch and grounded it to the battery and still nothing !! I used a jumper wire on the starter Solenoid , the motor will turn over but not start . I even bypassed both fuses and straight wired it to see if I could get a neutral light or headlights still nothing . What could it be ?
    • By middlebrookgt
      I have replaced the cracked stator cover on my non-running 2006 LT-F400F that I purchased recently, checked all the shafts vs the service manual and pics and advice here.  I replaced missing gears, bushings and washers, made sure that truth marks were all aligned properly, that the shift cam springs felt like they returned properly, etc.  IAfter installing the new stator cover I checked the transfer lever for proper movement from L-H-R and then cranked it up.  Happily, it runs and changes gears well in L,  but it will not shift into H or R for anything.  I have opened it back up and am going back through it looking for the missing puzzle piece(s) but how can I best check that I have everything right this time before buttoning it back up?
    • By Louznmemind
      (Question is at the end if you want to skip my blabbering) I got this unbelievably well taken care of Grizzly 350 in for a carb clean, it belongs to an elderly couple that bought it brand new in '07. Apparently whoever has been doing their oil changes for them never checked the air filter..
      Obviously it got debris in the carb, it would still run but only idle with slight choke. I've taken it apart and cleaned it, have new o rings, gaskets, etc. As far as the mixture screw is concerned, I'm assuming I obviously need to remove the plug. I'm mainly a lawn equipment guy, I've worked on slide carbs in the past but never an unmolested one with the plug still intact. I hate to mess with it as the carb had very little debris but I'm sure the o ring needs to be replaced at minimum. Finally, the question: what's the best way of removing the plug? I DO NOT want to mess up this carb..



    • By Louznmemind
      Can someone please tell me the fill point on the drive axle? '07 Grizzly 350, straight rear drive, not independent. Thanks 

×
×
  • Create New...