Quantcast
Jump to content


I have a 1998 Artic Cat 454 4x4. I have trouble getting full revs


Recommended Posts

I have a 1998 arctic cat 454 4x4 that will not at times rev high, cleaned carb & tank, has 700 miles on it. when it gets full revs it runs like a bear! sometimes at full throttle it seems to run half then takes off & runs great. cleaned carb,tank&plug any suggestions?

Edited by DirtDemon
Link to comment
Share on other sites

Sounds like you have an air leak. Red hot pipe + problems with a vacuum operated component tells me that you are sucking air in somehwere. My best guess would be it is between the carb and cylinder. With the motor idleing, spray carb cleaner around the motor. If you hear changes, that indicates that you are sucking in the carb cleaner and have found an air leak. You could also just be suffering from a clogged air cleaner.

Edited by DirtDemon
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By JohnnyB
      Greetings, 
      Have a 88 LT80 that been sitting for a couple years. Bought a new piston, cylinder and head. Installed these, rolled it over and it quickly locks up.  Took carb apart. It was full of what appears to be 2 cycle oil. Cleaned it, but keeps locking up and 2 cycle oil continues to seap from exhaust port.  When i installed new cylinder, I noticed crankcase was full of oil.  I'm now wondering if that oil is what's getting sucked up into cylinder.  Should there be no oil in crankcase?  If that the case, how is crank and rod lubricated?  Sorry, never worked on a 2 stroke. Thanks!
    • By 86ccord
      Starting this build thread to keep up with everything on my build and hope to motivate someone!
       
      I picked up this 2008 Yamaha Big Bear 250 2 weeks ago. A guy that I hunt with parked it at the hunt club for a year or so before I asked him if he wanted to sell. He said " fill my feeder and throw some batteries in my cameras, and you can have it". Sounds like a deal to me! 
      I have attached some pictures of how it sat under a tarp in the woods and when I got it home and cleaned up a little. 
       
       



    • By Spritee1
      having an issue with the unit when running under a load up a hill or in high gear, seems like the belt is slipping, there is a clapping sound coming from the primary clutch like it releases and snaps back in. i don't think I should have a noise like that. this is a friends unit and he has already replaced the primary twice with the same result.
      not sure where to look next
    • By ATVNetwork
      he fifth round of the 2024 ATV Motocross National Championship Series, an AMA National Championship, took place at High Point Raceway View the full article
    • Best Fit and Protection Guaranteed for all your cars, trucks, boats, jet-skis and more. Visit SealSkinCovers.com. Seal Skin Supreme Covers come with a Lifetime Warranty. Free Shipping!
    • By HSTAR
      Hey I have a 1997 big bear 350 4x4
      I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back  together and rode it I can't get it to shift in the right gears  I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N 
      Anyone know how to line up the shifter shaft and the shift cam s
       
×
×
  • Create New...