Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
Hoping someone will be able to help.
I have a 2006 Kawasaki Prairie 700 with twin Keihin Carbs CKVR D32. The Rear Carb is leaking out the side during cranking. it is not the float bowl overflow. It is on the opposite side of the carb from the diaphragm.
I got this bike not running and someone had already messed with it. I took the carbs apart , cleaned and rebuilt. Everything went pretty easy. It looks like it could be missing a small tube between the carbs but I have all of them listed in the service manual installed. See the pic for where it is leaking from...
Any help would be much appreciated.. Thanks.
I have a 2018 Kodiak 450 EPS that just this past Sunday I ran through a bit of water.
After the puddle the belt was slipping, so I pulled over and drained the ultramatic housing and the slipping problem went away. This was all in L and everything seemed to work fine. Later when I got on a road, I put it in H, but it still rode like it was in low... i.e. I had to rev it up a lot just to get to 30mph.
When at home I pulled the ultramatic cover off to inspect, and it looked okay in there. Not much dirt, belt and everything are clean, but when I rev up the engine (with cage in place, of course), the belt doesn't get to the top of the clutch (maxes out about an inch or 1.5" from top of clutch, so maybe it is normal).. I put it back together but same thing... H seems like L still.
Do you think the clutch needs to be further dissected for cleaning, or could this be an issue with the gear selector?
i have a older honda 350 cc quad that seems to start and other days will not.spark seems to be gone and there when it does run.I checked newer coil odd a older yet Honda but no help and idea I going to find the serial number as forget the year but believe around 1995 to 1997 year besides that great quad but cant run it so great this way and need it for chores around the acreage. Any help would be great. Ive check all fuses as well as the fusable ling which was fine until I screwed with it now need to buy another as have it wired not so safe.I handy but now have copd which takes away the brain power some.Any help would sure be appreciated
I picked up my first ever ATV on friday. It's an 89 Big Bear. It has some cosmetic issues, but seems pretty decent mechanically. I did have trouble getting the idle tuned to the book spec of 1,300 - 1,500 RPM. I took the carb apart and cleaned it out. Somebody must have lost the spring for the pilot screw, as it's no longer in the carb. Also, I have a dual cable carb, I noticed all the IPL's show the single cable carb, but I see others on youtube had dual cable carbs. When I would adjust my idle speed screw, nothing would happen. I bottomed it out and it didn't seem to make much if any difference. When i pulled the carb apart I saw the screw doesn't even touch the linkage, it's too short. Do the two different versions have different length carb screws? I'm wondering if somebody lost the ordinal, replaced it with the IPL number for a single cable carb which is shorter, and gave up on getting the ATV to idle. If you hold the throttle just a bit to get it to the RPM range listed above, it "idles" great. Any ideas? Or any links to the dual cable IPL?
Have you guys have good luck with the aftermarket intake boots? Or is this a buy once, cry once deal? I'm guessing the OEM units last longer, but there is a huge price difference. If you have had good luck with aftermarket, where did you get it? My current boot doesn't seem to have any air leaks, but it's encased in JB weld...
I'm getting a 9th digit check sum error on the ATV when I put the VIN in. Has anybody seen this before on a Yamaha? The VIN number looks original as well as the paint around it.
By crochet homemade
I have bought a 1996 suzuki king quad 300 and I have noticed that it smokes but I have put oil in it and plenty of gas had to fix shifter bc the nuts and bolts came out somewhere. I have had to replace the wire for the starter but now when I try to start it it wont idle at all and when it does run it smokes really bad like a whitish blue I guess, and it likes to stall a lot. So anybody can help me out please and thank you
Recently Browsing 0 members
No registered users viewing this page.