Quantcast
Jump to content

Recommended Posts

Posted

i bought a 2000 kawasaki mohave 250 water cooled, of coarse its not running i bought for $200 bucks, but came with brand good tiresPLUS some brand new tires not even mounted in the rims, anyways i tried checking spark by kickstarting it and no luck, any help would be helpfull, i need to know why its not getting spark, everythings plugged in, the coil looks good, could it be stator) magneto?? please help

Posted

Your best bet is to get a repair manual. There are some tests you can perform with a multimeter on some of the ignition components. That will either help you find the problem, or atleast rule a few things out. I would double check all wires switches and connections, test for power running through the ignition curcuits, check for blown fuses. You might try a new spark plug. I would also check the flywheel key to see if it is sheared off.

Posted

Probably not, if you connected the two wires that go into the key switch, you have effectively bypassed it. I would seriously just get a manual, you will want to have it anyway. The factory repair manuals are a bit spendy, but worth it. However, you can find cheaper manuals like Clymer manuals, for around $20-$30, still well worth the money.

  • 3 weeks later...
Posted
i also want to include that the key is missing , but i connected the 2 wires, could this be it??

That is your problem right there. For the mojave to run the ignition wires can not be touching each other or the chassis also check the kill swith in the run position with a multimeter you should measure infiniate ohm if you have 0 its won't allow the bike to fire. And no need to buy a manual here it is for free just make sure youblook in the back of it to see what has changed through the years. If it doesn't work let me know I have the mojave manual saved on my computer.

https://www.yousendit.com/transfer.php?action=batch_download&batch_id=VGlkckhYcVg4Q1IzZUE9PQ

Posted
So, then, is does that mean the ignition would effectively be turned on if he separated the wires? What is the point of the key switch, does it open or close a circuit to turn the ignition on?

Leave the wires open, not touching each other or the frame. turning the key on opens the stop circuit and allows the bike to run. I ran my mojave without the key and ignition switch for months just have to tape the end of the wires off so they didn't touch the frame. Other wise you'll have premature shut down or you'll be sitting there chasing your tail on why the bike wont start.

Posted

yea i tried it and no luck.. but i checked the stator and found a crack in the flywheel!!! i wonder if thats the reason for no spark?? since the flywheel is basically a magneto on these kawasakies

Posted

It is like that on all ATVs. I would think that you should still get spark, as long as the crack is not on the part of the flywheel that triggers the pulsar coil. However, it should be replaced because the cracked flywheel could turn into a broken flywheel, and that could cause alot of damage. So I would definately start with that. If you still have problems, try to find the specs for direct resistance testing on the ignition components.

Posted
yea i tried it and no luck.. but i checked the stator and found a crack in the flywheel!!! i wonder if thats the reason for no spark?? since the flywheel is basically a magneto on these kawasakies

that could be part of your issue. plus you might want to check the pick up coil is working properly that cause a lot of firing issues as well. In the manual there was a section on how to test it.

  • 1 month later...
  • 7 years later...
  • 2 months later...
Posted

Hey guys I bought a kawasaki mojave 250 year 2000. I have had it a month sounds like it has some piston slap on the right but not sure. Today I was on a ride and all was well I was about 30 miles from home ( normal ride not going fast. Do it daily ) and bike shut down making some crazy noises. Wont restart. Has good gas and oil. Any ideas, did the motor blow? Maybe because of timing? Any ideas cause I'm lost. 

  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By RGS
      1989 Moto 4 YFM350ERW intermittent spark.
      Quad has set for about 7 years and was running when parked.  When I replaced the battery and attempted to start it had no spark. 
       
      What I have done.  Followed troubleshooting in the manual. 
      1.       Coil failed the resistance check so I replaced it.  Still no spark.
      2.       I performed resistance checks on the stator and they all pass.
      3.       Found a bad rear brake stop switch and unplugged it and connected the wires in order to disable.  Now I have intermittent spark.  I believe that the issue is with either the stator or CDI and not sure which.
      1989 seems to be a transition year for electrical.  I can get new aftermarket CDI units for 87-88 and 90-94.  I cannot get ones for a 89.  I can get new stators for 87-89 and 90-95.  Looking at the schematics the wiring on my moto is closer to the 90 ones on the ATV side of the CDI and closer to the 87-88 on the stator side of the CDI.  Looking at part supply sources the stator housing is the same part # for all the years and looking at some of the stators on Amazon that have the dimensions on them both of the stators are the same size.
      What I am thinking of doing is to replace the stator and CDI with a 90-95 one as these parts are all readily available.   Does anyone know if this has been tried before and if there are any issues with doing this.  
       As a side note I also have a 1993 Moto 4 YFM350ER that has been sitting longer but it is located about 400 miles from me at this time.  By doing this change in addition to being able to get parts I will also have 2 ATV’s that are the same electrically. 
    • By Suzukiquad
      Hi, I have been around everything with a motor since I was little, and finally purchased more to get my husband, and kids involved. I have 4 quads I will be searching around for information on. I have two 2002 Suzuki LT80K quads, a 1997 Yamaha Timberwolf 250, and a 1996 Kawasaki Bayou 220. I have had different ones throughout the years, and plan on buying another Yamaha Banshee. I plan on trying to learn more about all of them, so I can customize some of them. I know nothing about them besides how to race them, my dad always took care of the rest, but figured it was time for me to learn. 
    • By BuckBilly
      Good morning to all !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
      Let's see if we can make this a daily event.
    • By kawasig
      Hello All
      I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
    • By Tim Keiper
      1st problem, Does anyone know where I can find a stock carb for my Timberwolf, I have tried two different aftermarket carbs and they both suck. The machine runs great until it gets good and warm, then it keeps stalling unless I feather the throttle. it will even stall while I'm trying to go from 1st to reverse or vise versa. I took it to a buddy of mine who is a bike mechanic for years, and he told me try to find a factory carb. When I look online from dealers it says "NOT AVAILABLE" anyone have any suggestions ?
       
      2nd, The small tab on the rear axle for towing is to short for even pulling my small yard trailer, I can't even turn a little bit and hit hits. I tried making an extension which worked great as far as length, but it bends the tab and then the extension drags the ground. I have an idea of what to do to fix it, but wanted to see if anyone else has had this problem and see how you solved it.
×
×
  • Create New...