Quantcast
Jump to content

Recommended Posts

Posted

I just dug my Outlander out of The snowbank last weekend (yes we're just in the transition from Skidoo to ATV Season)

I did my spring once over and changed the oil a few days ago and noticed there was gas in it. In fact instead of 3L of used oil there was 4.5 L of liquid....

After driving for a few days (maybe only 10 - 20 km) I rechecked my oil and it smells like there is some gas in it again.

Any suggestions on where to begin my trouble shooting?

Thank you

Jeff

Posted
there is one way in for fuel from cylinders but it have to be very high mileage on the engine and u feel less torque

Are you referencing worn piston rings?

Jef_In_Arviat, do a compression test. You may be getting some blow by gases into the crank case.

Posted

The only way that I know fuel can get into the crankcase on an EFI machine is blow by. Worn rings, damaged cylinder wall, or a damaged piston will allow compression to leak by the piston and into the crankcase. In a machine as new as yours, this is not common, but still possible. Using the wrong oil, not changing the oil, not cleaning the air filter are all things that can speed up engine wear. If the machine has been neglected, things can wear down pretty quickly. I would start by doing as Ajmboy suggested, do a compression test.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By Coyote251
      I am hooking up a speaker on the rear of bike and want to use a factory auxiliary switched plug and not have to cut into the factory wiring or add another switch. I have read a bunch of posts that say there should be an auxiliary 12V connector in the front and one in the rear. I found the one in the front when I hooked up my winch but cannot find any in the rear. I have seen some pictures showing one on the right side attached to the down tube behind the side cover, but there is nothing on my 2024. Can anyone confirm that there is a auxiliary 12V connector in the rear on the 2024 700 Xmr? If so, can you please tell me where it is (with a picture if possible)?
    • By Coyote251
      View File 2016 Can-Am Outlander 570, 650 & 850 L-Series service manual
      service manual - 2016 Can-Am Outlander L-Series
      2016 Can-Am Outlander 570, 650 & 850 Standard Series Here is combined the base manual along with all the needed updates and the 2016 supplement manual into one manual
      Submitter Coyote251 Submitted 01/03/2025 Category Can-Am BRP ATV  
    • By hporter1208
      Okay, so I have a 2002 Rubicon 500…bought it last year and it sat for several months until I put a new rear axle in, FINALLY got that done and was super excited to finally have my wheeler going, just to notice a strong gas odor. Popped the seat off and sure enough, pouring gas from the carb overflow. Fast forward a few more weeks and get the new carb and get it in, no leak! Yay. Except now I have no spark. 😒 I’ve tried another plug and checked and am getting no power to the coil pack. I’ve read and read and mostly what I’ve found is ECU, which is fine…but I like to exhaust all avenues before buying the more expensive parts just because I don’t wanna spend the money and it have ended up being something simple that I overlooked because I was trying to rush. 😂 I don’t know if it’s relevant, but I read on another post that someone had similar issues with theirs and it was the sensor on the side of the carb, just a thought since this literally happened after I put the new carb on. It also displays “- -“ on the display screen where it should show the gear position.
    • By huntindog
      I am in the process of puting it back together after replacing the DPS gearbox.
      The manual I have states that it will need to be flashed by a dealer. Is this still true?
      Also , I have a mystery bolt That I cannot remember where it goes. M6x 70 or so.  Hex head with a flat washer.I will try to attach a pic.
      Pic is no go for now....Cox issue I will try again later
      TIA
    • By Slitzer
      Hi,
      Thinking about to upgrade with a performance exhaust.
      Appreciate tips on brands and where to buy (ship to Europe)
×
×
  • Create New...