Quantcast
Jump to content

Recommended Posts

Posted

Hello I have an issue when the battery dies all the electrical componets start to fail.I removed the batery started it ran fine but nothing turned on no lights no cooling fan nothing.I though it can run without the battery.I think I have a alternator problem.:elvis:

Posted

Check all your body grounds first. Meaning take every ground off and clean them first. Check the tightness of the ground bolts. Once that is done then proceed with your troubleshooting. Guessing costs money so be 100% sure. D/L a shop manual and follow their test procedures.

Mario Welding Inc

Telecommunication

and Utility Equipment

Repairs

Posted
Check all your body grounds first. Meaning take every ground off and clean them first. Check the tightness of the ground bolts. Once that is done then proceed with your troubleshooting. Guessing costs money so be 100% sure. D/L a shop manual and follow their test procedures.

Mario Welding Inc

Telecommunication

and Utility Equipment

Repairs

^

l

l

I hate when I post from my company phone and forget to turn off the signature

Posted

Thanks I'll give it a shot this weekend.Funny thing I couldn't make out what your avatar said till I clicked on it. Very funny me and the guys in the office were dying!

Posted

I have to agree, check all your grounds. Also check your voltage regulator and stator. What does it read at higher rpms? It's a 12V battery and should be reading 13V + i would think.

I read somewhere that there is a recall on some stators. What year is your quad?

Posted
Hello I have an issue when the battery dies all the electrical componets start to fail.I removed the batery started it ran fine but nothing turned on no lights no cooling fan nothing.I though it can run without the battery.I think I have a alternator problem.:elvis:

If you can run it with out the battery then I would think that the problem is not your alternator, as the alternator is providing the voltage to provide spark. Did your gauge cluster die before this happened? (no speedometer, and Loss of 4 wheel drive) I know the units in the 2000's had an issue with water getting into the gauge cluster, and EVERYTHING runs through that damn thing.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By Joeguy
      After i did my rebuild it seems to not want to shift well. I think the cable is alright, and when it does shift its nice and solid. I have to basically use my hand to shift and i have to pull or push it very far, like max travel, to get it to shift. I also tried adjusting the clutch set screw. Any ideas where to go next, or maybe i should just grab a new cable to try.
    • By realpilot
      I am unable to find a wiring diagram for this UTV.  When I turn the switch to on, the contractor does not engage.  The Brake pressure switch and the parking brake switches work correctly. What else should I be looking for?  All of the diagrams I have found are for newer models and the wire color coding is different.
       
      Thanks
    • By OldATVowner
      Just getting into this issue really. Been replacing solenoids but now I'd like to track down the problem. This time I'm not getting neutral/reverse lights or start button. Was on a creek ride when it started doing this recently. It cranks by arcing the solenoid and gives me no light or start button but if I crank with the pull cord....the neutral light and the button work. Turn it off and try to crank with the key and nothing. I'm looking into the safety switch issue tomorrow and re charging the battery. Just figured this was odd enough of a problem that you guys might be familiar. Thanks
    • By Dsluder
      I am having an issue with a hs500. I bought it broken and have been trying to get it running. It seems to be starving for fuel. If I put my hand over the intake it will crank but will not run for very long because I'm not able to get the correct airflow with my hand. The things I have done so far are. Replaced the fuel pump, fuel filter, mass airflow sensor, idle air adjuster, fuel injector, cleaned the throttle body, replaced the ecu, and still the same issue. I notice the injector does not spray when removed from the head. I dont know if that is common. 
       
      I am out of ideas on what to do next. I have removed the fuel line from the injector and it is getting plenty of fuel. If anyone has an idea on what could possibly be the issue I would be happy to try anything at this point.
    • By Mikey509
      Hey guys, so I've been messing with my quad, and between all the starts, the battery is dead. Is there a certain way to charge these? Can I just throw a trickle charger on it and call it a day? can i also jump it like a normal car with a battery pack or is that to much voltage 
×
×
  • Create New...