Quantcast
Jump to content

Recommended Posts

Posted

The wheeler will start and idle rough, when the throttle is applied it will bog down and die. If you start it with the lights on low or high it will run but when the lights are killed it will bog down and die. It was recently timed at top dead center and will still roughly run. CDI box? I dont know what else it could be.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Thumpinhard25
      First thanks for any help guys, new to the forums and it's gotten me this far. I bought a 2001 bear tracker 250 for my family to get around the dirt bikes races. It wasn't running right and had a high idle. Previous owner thought it was a carb problem, so he ordered a new Zoom carb and new intake boot, but it still had the same high idle. ( I believe he had the throttle cable adjusted wrong, because it idled fine when I put it back together) So I tore down and cleaned the stock carb, and it started up and idled fine, but needed to have the choke 1/2 out to run.  I swapped to the new zoom carb and had the same issue. Choke half out bike ran ok. I played with the needle and the pilot screw with no change. ( bike did seem to be running rich though, but didn't get better when I tightened pilot screw or raised meddle) I Took it to the races and once I started bouncing around in the cattle fields the quad started cutting out real bad. It would barely run.  Sometimes it would run with choke off, sometimes choke 1/2, sometime choke full. I cleaned carb again, checked float level, and boots, no change still wouldn't run. Then suddenly it started running ok again.  This makes me believe it's an electrical issue rather then carb. I know there's no air leak, it's been checked, both carbs are clean( I've swapped them out a couple times, it starts up immediately and usually idles fine. But then bogs down/ or stutters under throttle. I saw the post on the guy who disconnected his rectifier and reconnected and suddenly it started working again, which lead me to believe it may be electrical and not carb.  So any advice on what I should check? Any way to test the CDI or rectifier?  Once again, I appreciate your help.  
    • By Tinkeringreg
      Hi my name is Greg and I just acquired a free 2000 yamaha kodiac 400 4x4 with the ultramatic transmission that does not run. I plan to get it going and use it around my property

    • By kaidella
      Bought 4 wheeler for kids. Used to run and soon as it was put in gear it died. I have put new carburater, new plug and battery. The neutral light won't come on. I replaced the solenoid, then the positive battery cable and today put new relay assembly on. Still no neutral light. Not getting any juice and I don't know why.
    • By P_syko
      Does the 1987 moto 4 350 have a low oil sensor that kills spark? Or are these too old for that kind of thing? 
    • By Sportsman500guy
      I bought a 1996 Sportsman 500 4x4 about a month ago, and I love it. Unfortunately, I've been experiencing a few problems with the high-range gear. The first problem is that the gear selector will intermittently pop out of high and into neutral. This problem will sometimes occur when starting from a stop and sometimes will also occur while at cruising speed. The last time this happened I stopped and put it back into gear, however, as soon as I tried to throttle the machine would die. I turned it on again with no problems put it back into high and it died again. Once again I turned it on with no problems put it into low instead and it worked fine with no problem. I drove in low down the road slowly for a little and then shifted back into high with no issues. 
         I plan on working on it this weekend and would just like some opinions or feedback from anyone who may have experienced these problems before. I'm very mechanically inclined but im unsure of exactly where to start as this is the first Polaris ATV that I've owned. Any feedback is appreciated and thanks in advance  
×
×
  • Create New...