Quantcast
Jump to content


2000 Honda 400EX Oil Filter Gasket


pato2387

Recommended Posts

yea the filter came with an o-ring but what i was wondering is if were the cover meets the crankcase if there should be a gasket in between that because it seems like the kid i baught it off of used a permatex on it or if it was just my fault when i installed it. i may have damaged the o-ring which could be causing a leak its only when its a cool temp when it is warm it does leak as much

Link to comment
Share on other sites

Yes see my previous post. Remove all of the permatex and install an o ring its about 2 1/2 inches in diameter. For this I would go to a dealer as the would have the proper size. Going to a hydraulic place they might not have one the is an exact fit and might leak again. Make sure none of that permatex got into your motor. It will damage your motor.

Sent from my SGH-T959V using Tapatalk

Edited by marioweldinginc
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Werewolf
      Oil is getting in the air box from crankcase vent tube, I put the two hoses that go to the air box together then something started to smoke on the front of the engine. There is a filter? In the line I blew that out.
    • By Brantley11
      Hey everybody,
       
      My proficiency is with Hondas and Yamahas make me see RED!
       
      This bike is my brother in law's, it has 1199 miles on it and went from running great to dead with no start. Every once and a while it will start and sputter for 2 seconds. It is extremely sporadic when it fires but never runs for longer than 3 seconds. 
       
      Here is where we sit:
      Brand New Fully Charged battery
      Carb was cleaned with air hose and carb cleaner then into the ultrasonic cleaner with Aircraft aluminum cleaner
      New Shindy Carb kit (made in Japan version)
      Cleaned out petcock and gas tank
      New 93 Non Ethanol Gas
      New Spark Plug
       
      It gets a spark through the spark test light every time
      Bluish white spark
      When holding the spark plug 1/4" - 3/8" away from head it will jump and spark to the head
      Good Compression
       
      Here are the readings:
       
      Pickup Coil 519 Ohms (range 459-561)
      Charging Coil 266 Ohms (range 270-330)
      Lighting Coil 0.700 (range 0.702-0.858)
      Spark plug Cap 10.58 Ohms (10kohms
      Ignition Coil Primary Coil 0.5 ohms (range 0.18-0.28 ohms)
      Ignition Coil Secondary Coil 8.20 kOhms (range 6.32-9.48 kOhms)
       
      Would y'all think stator and pick up coil, rectifier or CDI are the culprit?
       
    • By 86ccord
      Starting this build thread to keep up with everything on my build and hope to motivate someone!
       
      I picked up this 2008 Yamaha Big Bear 250 2 weeks ago. A guy that I hunt with parked it at the hunt club for a year or so before I asked him if he wanted to sell. He said " fill my feeder and throw some batteries in my cameras, and you can have it". Sounds like a deal to me! 
      I have attached some pictures of how it sat under a tarp in the woods and when I got it home and cleaned up a little. 
       
       



    • By JohnnyB
      Greetings, 
      Have a 88 LT80 that been sitting for a couple years. Bought a new piston, cylinder and head. Installed these, rolled it over and it quickly locks up.  Took carb apart. It was full of what appears to be 2 cycle oil. Cleaned it, but keeps locking up and 2 cycle oil continues to seap from exhaust port.  When i installed new cylinder, I noticed crankcase was full of oil.  I'm now wondering if that oil is what's getting sucked up into cylinder.  Should there be no oil in crankcase?  If that the case, how is crank and rod lubricated?  Sorry, never worked on a 2 stroke. Thanks!
    • By Mhatayas
      What should I do about this , bad oil leak where the filter cover bolts on . Can I use some gasket maker 

×
×
  • Create New...