Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

redneckyankee

1996 Yamaha Warrior Starting Problem

Recommended Posts

ok so i had or still have a electrical problem , i have replaced all the relay's and solenoid . the only way i get the thing to start is in gear with the clutch out . if i put in neutral it does nothing ,if i put in gear and pull the clutch in it still does nothing

:aargh:

Share this post


Link to post
Share on other sites


Did you replace the neutral safety switch?

* Added manufacturer and issue to thread title.

Share this post


Link to post
Share on other sites


usually a relay goes in only one way inside a socket. But the wires going to it could be crossed. can u twist the wires together on the neutral safety switch, bypassing the switch?

Share this post


Link to post
Share on other sites

Are you saying you push it to get it started with it in gear and the clutch out or it will start with the switch as long as it's in gear with the clutch out.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Daniel Gibson
      Working on a bayou 220 that has been ran extremely hard it's whole life. Literally had almost an inch thick dirt/oil covering the motor. Yeah that bad. Surprisingly it runs though. I cleaned the carb and tank multiple times. They're clean enough to eat off of. Readjusted valve lash and set timing. Was about 3 teeth off. It cranks good and runs good only problem is I have to cover the carb intake basically choking the hell out of it for it to start. The com choke works fine. It does this each time I start it regardless of temperature both ambient or motor. Wth? Compression is at 115psi I get 130s if I put a little oil in the piston chamber. Please help. Thanks 
    • By Mike Johnson
      Does anyone know what the 3rd item is behind the battery on this ATV ? I know 1 is the,  solenoid1 is the CDI box, what is the 3rd.
    • By Scott Sirr
      I need to figure out how to clean/fix or replace my neutral switch assembly On my 2008 Yamaha big bear 400 as generally the neutral light doesn’t come on when it is in neutral. To get it to come on I have to wiggle the foot shifter and hold it in just the right spot.
      I have googled it and can’t find much on the 400’s. I can’t find a service manual online and the parts manual is super vague.
      I think it is in the right side engine cover area, but not certain. 
       Any help would be great. thanks
      Scott
    • By jake Stillman
      Hello I am new to this forum and lt80s I have an 87 that has burned up 3 coil/cdi combos my question is can I out the newer set up on it and if so how do I do it I know they have different number of wires going to the cdi mine only has 2 please help
    • By JC4x4
      My Honda Fourtrax won't start. The starter is kicking the engine over, but it won't start. It sat for about a year while I was living away, so I thought it might have been bad gas. I completely drained the fuel, flushed the fuel lines and filled it with fresh gas. However, still nothing. It started and ran fine the last time I used it. Any suggestions on how to diagnose this? It could be fuel or electrical at this point. Is there an easy way to rule one or the other out? Thanks
  • Similar Tagged Content

    • By quadtech62
      I have a 02 Warrior i am trying to build a wiring harness i have looked in the manual and  i am confused... the pick up has 2 wires.  W/R W/G The source rotation coil has 2 wires. One is Red other is white/blue. The manual shows the  the white and blue wire connected to the w/g  right after the stator... so why is these 2 wires connected?  Does not show w/b wire at cdi 
      i have looked at many options with no luck if someone has a 2002-2004 warrior and can take a pic of the wires and location at cdi i would really appreciate it. Thanks
    • By Chase Cook
      I have a Yamaha 350 in at once to try to fire up but won't. It's getting gas fire air and it has a lot of compression but still struggles to start check the timing it's top dead center valves are good valves are adjusted everything's working but won't fire I put my hand over the carb suck in gas and it tries to but it makes a lot of black smoke. Also when I put my hand over do you carb and tried to start it there's black black nasty stuff in the gas. So I don't know if it's trying to burn too much or what it is the gas tank clean and it anything to do with the gas it's with it firing. Took the spark plug out and it's pure black. What is dried up black not nasty corroded wet looking. Need help to solve the issue
    • By Chase Cook
      I have a 2001 yamaha warrior YFM350x and started to work on it. The person who I got it from put a new top end kit in it. I already took the top end off and checked, brand new still. Had to clean the valves so it can get better compression. Put it back together and turned it over and and made good compression but also had a loud clanking noise at the bottom, put hand over carb and stopped making the noise when I turned it over. And won't start.  I know it is not the top end. Just cleaned it and valves. Need help trying to figure out what's the problem.. thinking it's the crank rod but don't know. If it is the rod can i just get a new rod for it?(would be great if so). Or does it need a hole bottom end . In need of help.
    • By Colby Calk
      I recently got a 98 warrior 350 that 'needed the carb adjusted' but the reality is it has no spark. I have a new spark plug, plug wire, ignition coil, battery, and cdi box. I checked continuity and took apart and inspected the starter/kill/light switch on the handle bar, and it all looks brand new and checked out. The key switch seems to be working properly, as when off, nothing works, but when switched on, lights and electric starter button work. It turns over fine, and as I just stated, all the lights work. I took all the plastics off and traced all the wires, and only one had a small cut in it, but it was only through the rubber sheathing, not the wire itself (the blue one coming from the stator). I cleaned some grounds, made sure both relays work, and still nothing. I pulled the stator cover and looked at the stator itself, and it looks great. No broken wires or connectors or anything. Still, no spark. I'm at a loss. Where do I go next? Any help is appreciated.
    • By Brad Lawson
      Hello all, I’m working on my sons 99 Yamaha Warrior 350. When I pulled the plastic cover off left side of engine, I can see oil leak at the seal. I pulled the bolt out and then the starter boss(I guess that’s what it’s called?) I can see that the boss doesn’t make contact with the seal. Is there a spacer of some type that slides on to the boss, to make contact with the seal? This seal is held in place with a plate with 3 screws in it. This boss slides into the bearing in the stator. I have been to parts websites and I don’t see what I’m needing. Maybe it’s just the wrong seal?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...