Quantcast
Jump to content

Recommended Posts

Posted

hey guys, I have a 2004 400ex. I just installed a 426 big bore with new weisco piston/rings. The first start went good for about 10 seconds, it started right up with no hesitation, then it started blowing whitish blue smoke out the exhaust badly, after that it started blowing oil out of the exhaust. I think the o-ring at the bottom of the cylinder that sits around the sleeve ripped when installing. my engine also use to smoke a little when cold before the big bore kit then stop after warm, which was due to my valve seals, i also believe the valves came a little loose but not bad. The bike runs great, starts great, full compression, no power loss. i will blow through my entire oil reserve in maybe 30 minutes, thats how bad its shooting the oil out the exhaust. What do you think the issue could be?

Posted

after first start I took it out to an open area and ran it for 15mins and got on it a little but not too bad, then shut it off and let it cool down.. then I started it again and ran for 30mins same thing.. by this time I ran out of oil. I used Rotella 15w40 for break in, not sure if that could cause any issues?

Posted

Yeah, I'm thinking a small part of the problem was how it was broke in. On my motor, I let it just sit for 15 minutes idling, then let it sit until it's stone cold. Then let it idle for 30 minutes, then cool down. Then 45 minutes idling, then cool down. Then beat the crap out of it LOL.

Posted

I have bought new rings, gasket set and valve seals.. just waiting for it to get a little warmer out to install them. Im hoping that those will fix this issue..

Posted

I haven't really ran into it overheating besides letting it idle for like 10 minutes without any movement, but I was definatly thinking of going the spal fan route for extra piece of mind.

Posted
yes can do tht also:yes:........ so hows ur ex goin mario:wink:

Waitin on the motor, cleaning up the frame and plastics, changing all the bearings, collecting 450r shocks and having em revalved, straightening rear axle again. Adding some cooling tricks too! Im hoping all is back together by end of march but now it doesnt look it

Sent from my SGH-T959V using Tapatalk

Posted
I haven't really ran into it overheating besides letting it idle for like 10 minutes without any movement, but I was definatly thinking of going the spal fan route for extra piece of mind.

I havent had the experience but of what Ive read so far its not so much of an overheating problem with the motor but alot of the time its the carb getting heatsoaked from the additional heat the motor puts out. A warm carb heats up incoming air and causes the bike to be down on power. Sometimes its confused with overheating. Whether its true or not im not sure but a heatsoaked carb was an absolute nono when I was dragracing back in the day. In between runs we would put bags of ice on the motor and put a box fan on top of that. How to solve this on the trail i havent figured out yet but I will. I have one solution which involves Co2. I need to figure this one out though.

So far my cooling tricks involve a fluidyne cooler, spal fan, scoops and maybe a Co2 or water setup. Nitrous is too expensive.

Sent from my SGH-T959V using Tapatalk

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By rjsummer
      Just picked up an 84 LT185 ATV, I understand there was an accessory add  on that gave it electric start, anyone have any info about that kit? 
    • By Rockbottom
      2008 400 big bear was running now will not start
      have power to relay, in neutral, press start have power to starter but nothing happens starter does not turn
      i have good ground at battery to frame and added ground from wire harness to frame beside batter/ frame ground
      blue white wire to cdi has power with key on
      I believe the neutral lock out is working since is was before i shut it down
      if i put  it in gear and hit the start button with key on the relay does not click or send power the starter
      The 3 wires at the relay have power with key on
      What should i test next?
      thanks ahead
    • By Mister907
      Hi guys, I have a 2004 big bear 400. Last winter while plowing the driveway, I heard a loud pop from the left side of the engine. It continued to run as I looked for leaky fluid, but then died shortly after backing it up and won’t start now. The oil light comes on when I try to start it, no noise or anything else. 
      No blown fuses that I can find.
    • By Brent Wright
      What's a good size to start a 10 year old on?
    • By HeWasRidinDirty
      The one I need to replace has a 2 wire plug coming out of it. Searching eBay I see tons of them with only 1 wire . WTH???

×
×
  • Create New...