Quantcast
Jump to content

houser steering stem

GREENIE

By GREENIE
in General ATV Discussion

 Share

Recommended Posts

WillyPoP Proficient

WillyPoP

Posted
Posted

they help...but if u just make sure to re-oil them and they are lubed up, you should be fine. just make sure you tighten the stem to the bearing plate well or u will feel a small unusual "tink" feeling when u move the bars back and forth

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • LCP92
      Leaking valve seals?
      By LCP92
      Guys, I've got a 1999 Honda Foreman 450S.  It runs great, but smokes out the exhaust after startup until it warms up.  I'm thinking the valve seals are leaking.  I was wondering if there is a way to replace them without removing the head or if there's an oil additive that will recondition the rubber seals.  Any advice?
    • Gtc4d
      need help on a yamaha raptor 80 stalling
      By Gtc4d
      I recently purchased a raptor 80 for my grandson for  christmas. I am trying to make sure it is running properly. i have rebuilt the carb and adjusted the carb idle then the mixture to middle of where it runs rough and it runs great for about a min or 2. then it stalls out. I can usually choke it and it will start so i feel it is lacking fuel. the fuel shutoff valve has been changed and i checked it for good fuel flow.  any ideas of what to check next. I am planning to vfy fuel float height tomorrow. I visually checked it by turning carb upside down when i had it apart and it looked level. any ideas are appreciated. 
       
      Thanks.
      Todd
    • jordan_ATV
      Raptor Pre-ignition?? (Maybe)
      By jordan_ATV
      I got a 2005 350 Raptor Special Edition and I'm dealing with a no start issue; the weirdest thing is when I'm cranking it fires and slows down showing signs of pre firing, smoke shoots out the carburetor every time it sparks. every electrical part (CDI, Rectifier, Stator, Coil) has been swapped out from previous owner, the top end of the engines all new and I cleaned the carb out, anyone got any ideas or similar problems, also is it possible to have a bad spark timing
    • kawasig
      I just bought a rare beast!
      By kawasig
      Hello All
      I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
    • Norseman69
      Hi everyone bought an lt230e 1993
      By Norseman69
      Hi. I just bought an lt230 1993.  Ive started buying parts for a full rebuild.  But somehow beskepedal has been removed and pegs welded to where They are supposed to be screwed.    I was wondering if anyone have one and Could measure how far out the pegs are.  Like the peg the brake is put on and then peg outside of it.  And the one lower down.  So i can recreate them. 

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...