Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts

Was about to change the oils on the TaoTao atv.

Its an automatic, no gears or only one.

Problem is that I only found one place to fill oil instead of two.

Could it be that it use the same oil for the engine and autogearbox?

If it like that what oil should i use? Transmission or 4-strook?:huh:

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Ben Cramp
      I am hoping one of you knowledgable people can answer this for me. I have a yfm200 moto 4 engine I want to put in an off road go kart. I would like to mount a sproket where the drive exits the case before the u joint so that I can get rid of drive shaft and make engine bay compact. To do this I would mount engine 90° to axle but would also need to tilt it forward 15° to account for the angle the drive exists rear of casing. Would that be ok? Would oil pump etc still work. Any advice greatly recieved.

    • By Ted Craig
      I know a lot of people say not to use anything but Oem. For the sake of the those who chose not to, or the OEM part cost more than the project, lets hold back negative comments. 
        I just purchased a carburetor that is supposed to be up to OEM specs. The company has a good reputation on eBay and Amazon. The Carb is supposed to be for this bike and jetted exactly. 
        This question should basically go under carb adjustment. I installed the new carb, the bike idles fine. On throttle it sputters half the time and the other half it will rev up fine. Does this sound like the needle is set at the wrong point? Does it sound like the main jet is the wrong size? Or is there another adjustment besides the air/fuel screw thats is 2 turns out? 
        Yes i could truck through old threads and possibly find the answer, but i thought it would be nice to have one tailored to new carb installs. 
    • By Jeff Miller
      I'm trying to troubleshoot a starting issue. For a while, maybe a year sometimes I would hit the starter button and I'd hear a single loud click, but the starter wouldn't turn. Usually if I could pull the pull start or roll it in gear it would then start. (now I'm thinking that was coincidence) Now it only clicks. I tried to check what I could, battery is good, solenoid clicks strong, cleaned all connections (which were 80% clean anyway). I started thinking the starter wasn't spinning. I pulled it and it spins freely. The gear that it contacts in the engine-I can wiggle it maybe 1/16th to 1/8th inch back and forth. When I reinstall the starter I feel it jerk when I hit the button. I'm thinking maybe it's the starter clutch? It seems when there's a problem with them they usually just spin freely and don't engage at all. Is it possibly something is causing it to lock? I'm a bit lost now.
    • By Wayne Starz
      I have a 2005 Suzuki Vinson 500cc automatic 4X4. I can only shift it in to park & High gear, it will not go in low or reverse, what's the issue & the fix?
  • Similar Tagged Content

    • By Craig Newton Lawton
      Hi thanks for adding me on here, i bought a none running 110cc thundercat quad and i have spark, fuel, compression but it wont start anyone have any ideas as im stumped 
    • Guest
      By Guest
      Ok...I'm gettin' me juevos ready to do an oir filter clean....
      Went to my local harley/quad dealer and he had me purchase the No-Toil kit (Cleaner, Air Filter Oil, Rim Grease)
      What I've read is that the No-Toil cleaner will NOT clean
      other oils off air filters....just the No-Toil oil....
      So, I've also read that others have cleaned their air filters
      in the kitchen sink, used gasoline, or used flash solvent....
      Looking for advice as I've mentioned I'm very mechanically
      DECLINED!
      I'm going to wash the air box seal in the sink and give it a good dry....
      One more thing......No-Toil or Bel-Ray for filter oil?
      Thanks!
      -TD
    • By toonces
      Have a 2011 Grizz 700 and for the diff oil the manual calls for SAE 80 API GL-4 hypoid gear oil. I'll be using Mobil 1 synthetic but as it comes in two different weights I'm not sure which one to get....either the 75W-90 or the 75W-140.
      The 75W-90 is listed as GL-5 and is recommended for use in 'high-performance vehicles like SUVs, vans and light duty trucks.' The 75W-140 weight is also GL-5 and is recommended for 'high-performance vehicles including sport utility vehicles, vans and light-duty trucks.'
    • By toonces
      Have a 2011 Grizz 700 and for the diff oil the manual calls for SAE 80 API GL-4 hypoid gear oil. I'll be using Mobil 1 synthetic but as it comes in two different weights I'm not sure which one to get....either the 75W-90 or the 75W-140.
      The 75W-90 is listed as GL-5 and is recommended for use in 'high-performance vehicles like SUVs, vans and light duty trucks.' The 75W-140 weight is also GL-5 and is recommended for 'high-performance vehicles including sport utility vehicles, vans and light-duty trucks.'
    • By bradleyheathhays
      I'm going into my '11 Grizz 700 to adjust valve clearance for the first time and when I button everything back up I'll be replacing all the gaskets / o-rings. The 5 I'll be replacing include (from the top down) both valve cover gaskets, cylinder head cover gasket, and the 2 gaskets in the crankcase cover.
      Do I need to coat these gaskets with motor oil before putting them on like when replacing your oil filter?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...