Quantcast
Jump to content


2004 Suzuki Vinson wont run


biggdave92

Recommended Posts

I am working on a vinson for a friend and i cant figure it out. I am getting spark. Carb has been cleaned. I soaked it for about 3 hours, rinsed, blew out passages, and re assembled. The bowl gasket could stand to be replaced but i didnt have parts at the time. I did look good enough to make a good seal though. Also, the air filter is removed. I am waiting on a new one to come in. So, when i first got the 4wheeler from him, he said it wouldnt run. i charged the battery, put some fresh gas in it and cranked it up. Next day i put a little seafoam in the tank, removed the air filter, and it wont crank. i held my hand over the intake with my fingers split to create a little suction and it still wont do anything. i've sprayed starter fluid into the intake, wont bust off. i cleaned the carb, still wont start.

i'm thinking the motor is not getting gas. also, i should add that the petcock is in the "PRI" position. Reason being is that when i disconnected the gas lines from the tank the only position that gas would run out is in the "PRI" position. when it is in the "on" or "res" position no gas runs out of the tank. Also, when i re installed the carb i put the petcock in the PRI position for about 1 minute to let the bowl fill up and i then removed the drain screw in the bowl to see if the bowl had fuel in it. It did not. No gas drained out. I checked the lines, they are clear.

also, i'm used to carbs with main butterfly and a choke butterfly. this carb has a main butterfly and some type of thing that slides up and down. what is that? how does it work? is it temp controlled?

ideas? thanks for any help!

Link to comment
Share on other sites

no, i havnt put any gas in the cylinder via the plug hole. also, i pulled the plug out and laid it near the plug hole and turned it over to check spark and it was sparking very well. i know jack about these machines.

what is that big thing that slides up and down inside the carb throat? some type of choke? i'm not talking about the throttle butterfly.

Link to comment
Share on other sites

Just a suggestion. I had a similar problem with my 02'...No start, acted like it was flooding, had great spark...It really had me stumped. Just for sh**s and giggles I swapped in a brand new plug and it fired right up. Just because you see a spark on the plug while its out doesn't mean it's sparking across the electrode where it's most needed in the combustion chamber. Just sharing an experience. I had mine tore down pretty bad and it ended up being a simple thing. It's worth a shot.

Link to comment
Share on other sites

Just a suggestion. I had a similar problem with my 02'...No start, acted like it was flooding, had great spark...It really had me stumped. Just for sh**s and giggles I swapped in a brand new plug and it fired right up. Just because you see a spark on the plug while its out doesn't mean it's sparking across the electrode where it's most needed in the combustion chamber. Just sharing an experience. I had mine tore down pretty bad and it ended up being a simple thing. It's worth a shot.

absolutely worth a shot!!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Mhatayas
      My uncle bought a Baja 250, 2006. Knew there was no spark since the get go. He don't know anything about quads so is getting me to help him try to get it running...
       
      battery is bad so I connected battery charger to it to crank it over , cranks over well , but no spark .... 
      Lights and everything work fine , but with each crank over using the e start switch , the display reads 999 888 777 666 ... Right down to 000 and repeats itself . 
       
      He managed to get a parts bike , I changed over the CDI and the coil and the stator from the parts bike and there was another black box by the voltage regulator I changed over ... I used my multimeter to confirm as much as I could works , it's hard without knowing which wires are which , and I cannot find any diagrams online for this bike ? 
       
      Do you think it could be the Killswitch? There's so many wires coming from there I don't know where to start . Also I should mention it appears the fan on the front of the bike has been taken off (the wires have been cut too ) 
       
      If this bike sparked it would run . The previous owner said he parked it one day and it just wouldn't start after.
    • By Clydaho
      2022 Sector 550, 414 miles on it and the gas gauge reads empty.  I topped off the gas and it didn't change.
      There is no fuse that I could find.  No access at the gauge cluster.
      Wiring on the top of the tank looks good, properly connected.
      Could the sending unit in the tank be stuck or broken?
      Has anybody removed the tank lid?  Any tricks?  
      Any other ideas?
      Thanks for any help,
      Clyde
    • By Uglyside38
      I have a 1988 Quadrunner 250 2wd. My brother in law sold it to my son for $20...had been sitting outside for several years. Got it home and had it running in about 30 mins. Ran it a bit and then went to looking at the carb as it was having trouble idling. Was getting it pretty close, then started losing spark...Also, it wouldn't start up every time...only about 1 in 5 tries. Anyway...now, it has what I can only describe as "intermittent" spark. I can get 1 light spark right when the start button is pressed and sometimes one when it's released...but none while cranking. 🤷‍♂️

      I have replaced the spark plug, ignition coil/wire, and traced wires best I can. I noticed a couple frayed wires at the pickup coil where it enters the case. So, now I have the cover off, stator and pickup coil out and trying to test the coil. I do have about 114 ohms resistance for pickup best I can tell. And I can read minute voltage when I drag a magnet across it. Could it still be bad? Can a bad ignition switch/button cause this? (I did have the switch off to oil the choke cable)...pulling rope makes no difference though...any ideas or help would be greatly appreciated!!! It's the intermittent part that's throwing me off! 

    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • By DarkRider
      This is something I'm extremely curious about. Has anyone ever attempted to buy a quad (or any other vehicle) from an impound lot? I've always wondered if this could be a bargain, or a waste of time. Google searches do turn up some helpful results. Looks like the state of NJ holds auctions online which I'd be a bit hesitant about.
       
      My online searches haven't really turned up any results of anyone buying an ATV this way. I'd be really curious if anyone tried this, or knows someone who has. I've actually found a couple pages with online auctions for my state, but none had ATVs.
×
×
  • Create New...