Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

surbike11

2007 Arctic Cat 700 EFI NO SPARK PLEASE READ

Recommended Posts

Thanks in advance for any help or guidance. I was out riding the other day and lost all spark. I have read every thread on every forum that I could find and have not found an answer. I have checked the codes and its 00. I have ohm metered the stator and crank sensor. I have also replaced the coil pack. I have inspected and cleaned all connections. I do not mud the machine, it is mostly used at the hunting lease for working plots. When I installed the new coil I held the plug on the side of the engine and got 2 little sparks when first turning over and then nothing again. When you turn the machine over like this it eventually flashes EFI on the screen. I checked both wires that go to the coil and noticed that both have ground continuity. While turning over the blue and white one cycle from around 1v to almost 12v. The battery has a full charge and I am at a total loss. I took the kill switch apart and all looked well. Oh yea and all fuses are good. Help me please I am getting very frustrated. Thanks

Share this post


Link to post
Share on other sites


I have not checked that. I honestly figured since it was spinning over that it wouldn't be that. That said I am not even sure where the neutral safety switch is lol

Share this post


Link to post
Share on other sites

it should be on the backside of motor ... looks like an oil sending type unit, probably 1 wire ... if the safety switch is damaged, its an easy fix, all it does is allow spark when in neutral ... i have seen some bikes that have a light saying they are in neutral and no spark, replace and spark again ... hopefully this is all it is ....

Share this post


Link to post
Share on other sites


Just an update, I have ohm checked everything and pulled all plastics off. I haven't found a smoking gun. I am starting to think that it may be the ecm, any thoughts out there on that being the condition? Thanks for the help please

Share this post


Link to post
Share on other sites

last thing I had do that was an 04 arctic cat 90, did almost the exact same thing, it was the cdi box. have you checked the rectifier? I doubt that's it but I would check it. also it may sound stupid but smell the cdi or ecm, usually if they are bad they will smell burnt.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Dwight Williams
      Hey everyone, I've been scratching my head over this for most of the day.  I bought a couple of Bayou 220's, got them running (they've both been sitting), and started tweaking and fixing small things.  One of them is mostly done, the other had an aftermarket carb on it and I've been trying to sort that out.
       
      Anyway, while adjusting the carb it died a few times, I restarted and moved on until it died and wouldn't restart.  I figured maybe I'd flooded it or something - after further attempts I realized I had no spark.  Since I have two identical machines I have many parts at my disposal.  I've swapped the CDI, spark plug and coil with no luck.  I have good resistance readings from the stator and pick up (135 and 110 respectively),  I don't have a peak voltage meter but I measure around 53VAC on the stator when cranking.  I have a 4 wire stator, not an alternator like the newer ones.  Grounds look good, I've checked the kill switch by verifying that it and the ignition switch grounds the black/yellow wire to the CDI.  I can turn the engine slowly and see the pickup short the meter as well, seems normal right?  So far everything I've checked looks the same on both machines.  I've got the service manual and wiring diagrams.  Do these readings make any sense?  I'm obviously missing something but I'm stumped.  thanks!
    • By Ajmboy
      Tonight is the first presidential debate and it should be a record breaker for viewing. Might as well have a mini poll here on QUADCRAZY to see how they stack up. Make your choice in the poll and feel free to comment in this topic. I'm going to pin this topic and keep it going through the elections in November. 
    • By BAMFUPINYA
      Any current Northern AZ folks out there on this forum? Im up in Flagstaff. Any organized rides anyone knows of?
    • By Colby Calk
      I recently got a 98 warrior 350 that 'needed the carb adjusted' but the reality is it has no spark. I have a new spark plug, plug wire, ignition coil, battery, and cdi box. I checked continuity and took apart and inspected the starter/kill/light switch on the handle bar, and it all looks brand new and checked out. The key switch seems to be working properly, as when off, nothing works, but when switched on, lights and electric starter button work. It turns over fine, and as I just stated, all the lights work. I took all the plastics off and traced all the wires, and only one had a small cut in it, but it was only through the rubber sheathing, not the wire itself (the blue one coming from the stator). I cleaned some grounds, made sure both relays work, and still nothing. I pulled the stator cover and looked at the stator itself, and it looks great. No broken wires or connectors or anything. Still, no spark. I'm at a loss. Where do I go next? Any help is appreciated.
    • By Quadtriumph
      Was looking for people to tell me some of the better trails around provo? Maybe meet up and ride. Thanks
  • Similar Tagged Content

    • By mikeexplorer
      Wiring diagram for 2007 Arctic Cat 700 EFI 4x4
       
       
    • By gregj49
      Blows out black smoke when you rev it up how do you adjust the carb?
    • By Barrysquad
      Somehow I lost all of my spark on my 350Big Bear, its a 1990. It ran well for maybe 3 days! Thought it was the carb. Cleaned it 4 times. It was losing power at midrange. Got worse and worse. Finally nothing!
      Are these good coils? I was thinking I could swap?
      2002 Honda-200cc: primary 0.4(ohm-200) secondary 9.0(ohm20k)
      1990 Yamaha-350cc: primary 0.8 secondary 11.0
    • By toonces
      I'm wanting to run Shell Rotella T6 synthetic in the 700 Griz but I can only find it in either 0W-40 or 5W-40 weights, and the manual says it's ok to use everything BUT those weights...5W-30, 10W-30, 10W-40, 15W-40, 20W-40 and 20W-50.
      Would it be ok to use the Rotella 5W-40 or do I need to stick to what's specified in the manual?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...