Watch Yamaha Grizzly 700 SHRED the MUD
-
Similar Forum Topics
-
By STLJ
Hope everyone is having a great weekend,
While riding my quad just quit, I mean dead. No life on the dash, no crank and obesity no start.
Had a quick look under the plastic, batt reading 12.7v power at the key switch.
Changed the power pack, still no luck.
Anyone else have similar problems?
I don't see a fuse box/panel, is there fusible links in the system? If so where di I start looking?
SK
-
By kawasig
Hello All
I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
-
By beast6228
It's been a long time since I have used a forum, I was the admin of one for quite a few years, had thousands of daily active members, with lots of crazy posts and spammers, so I salute the admins. Anyway, just waving my greasy hands, Hopefully I can help others out.
-
By dlgg7
I've had this for probably 15 years. It ran great till 4-5 years ago, mainly riding the grandkids around our fields, till it wouldn't start. It sat for a couple of years till I bought a new battery, but couldn't get it to even hit, so rebuilt the carb, put on a new fuel pump, but no go, so it's sat. Several days ago, charged battery, cranked over and it started??? OK, idles good, but won't rev up, so emptied gas tank, flushed out and filled w/good 93 octane, pulled pump line from carb and have good full line of fuel cranking over. New spark plug, good spark, old one black BAD! Oil change, adjusted valves, no difference. Pulled carb and took apart and cleaned, didn't find any clogs or crusted up inside. Now I've had the carb back off probably 6 times checking, double checking anything I can think of. No gas blowing back in air box. It idles good, can increase throttle up some then starts popping and dropping rpms off and if I don't let off the throttle, it'll die. I've read for 3 days now MECHs and RANDY walking several thru tracing the same problem, tried MOST of the direction given. ??? 
-
By DayBreakJim
So my latest wheeler is a 04 Yamaha Bruin 350. It had all the wires cut from the stator and a few others and no wiring harnesses. The previous owner had them all twisted together and the bike neutral light would come on it would start (hard to start) but then would idle fine. It would die when you gave it gas so I soldered all the wires together and went on inspecting assuming it was a carb issue. Later after the carb was cleaned and adjusted I got this (see video). The bike would want to die anytime you gave it gas and there would be this horrible knocking sound but only when you gave it gas. I was worried it was the rod bearing and electrical still messed up somehow.
Upon further inspection of the wires coming from the stator there was a W/R wired to R and a R wired to W/R. I switched them so they matched per the service manual (W/R to W/R and R to R) and the bike started right up, idled and revved out fine and the knocking noise disappeared. This was the problem the whole time. It was just really hard to tell bc the oem wires coming from the stator were so brown and dirty I could barely make out which was which.
Where the hell did that knocking noise go? and what was causing it?? Just racking my brain trying to figure out what it was so I know for next time but I can't make sense of it... Really thought it was the rod bearing but it didn't make the noise at idle so I was questioning it...Luckily I kept searching!!
20230725_171507.mp4
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.