Quantcast
Jump to content


Kawasaki Lakota spark issue


Todd Trask

Recommended Posts

24 minutes ago, Todd Trask said:

Well, I received stator, pick and new key switch asembly. I have great spark. Thanks to all whom responded.

NOW it Starts up with hesitation. Idles good , give a little gas it boggs down, back fires & dies instantly. Will start up after it back fires

DID I MESS WITH TIMING

It sounds like its running lean....what kind of carb you have? Air/Mixture screw and your idle screw,but you say it idles good,try the Air/Mixture one,but you have to warm up the engine and close it all the way, not to tight,you don't want to damage or brake it,slightly snugged,then turn it counterclockwise about 3/4 or 1  1 /4  turn then wait about one minute listen to the engine,you might have to play with that for a little until you get the adjustment you need...

Link to comment
Share on other sites

It only back fires now, won't run..😩

Makes one hell of a boom..

Went to try to start to warm up,

Just a recap..

1st time I started it. I let it idle long enough to install front rack, rear fender & rack., while installing items I gave a little gas and it would still bog down . jumped on and went 50 ft before it just died. Try to start it and it back fires

Will fuel will cause a huge back fire..?

Link to comment
Share on other sites

Ugh amazon carb.  No good. Replacement carbs should be oem! If you still have the oem carb then spend the money on a rebuild kit and rebuild it.   It’s not difficult and we will help you along.   If the stator and pick up coil were put in right which I’m  sure you did and no you can’t screw up the timing by doing what you did then my suspicions are the carb is the problem here.  

Link to comment
Share on other sites

Amazon has it and prob better off on eBay.   Look for the oem label when buying.   It’s worth it. You will rebuild the carb and set it up the bike will run great.  Just take a look on YouTube on rebuilding if your not familiar with the work and take your time. Clean work area.  I like to use a cheap white pillow case when doing a carburetor. Makes easy work when dealing with small parts on a white surface as well as seeing what comes out of the carb dirt wise .  Any questions you have we will help.  Post pics when your not sure and you will get pointed in the right direction.   

  • Thanks 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By newguy024
      Just got into ATV riding just last week, never had much money so i couldnt afford to buy anthing, so now at the age of 34 i just bought a 1987 suzuki quadrunner 300 for 500$ took it out a few times and what a rush of excitement to go through that first mudhole haha!
    • By BuckBilly
      Good morning to all !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
      Let's see if we can make this a daily event.
    • By justent_88
      Hello, im looking for some input on this situation i have. My 94 Mojave has no spark, and i have no idea what it is. Ive replaced/tested the magneto, the pickup coil, cdi, the ignition coil. Even the key and Killswitch. I haven't tested the harness its self, but i have tried another harness and still nothing. The only thing i can think of is the fly wheel itself. I have found a lot of metal shavings in the fly wheel and have cleaned it the best I could. But nothing happened afterwards. I am truly stumped here and hoping some of yous could shed some knowledge/ideas that could help get this thing to fire. 
    • By mga
      I see quite a few ads for that  Tribotex additive. It's kind of expensive, has anyone used it it their ATV or any other vehicle?
    • By Mhatayas
      My uncle bought a Baja 250, 2006. Knew there was no spark since the get go. He don't know anything about quads so is getting me to help him try to get it running...
       
      battery is bad so I connected battery charger to it to crank it over , cranks over well , but no spark .... 
      Lights and everything work fine , but with each crank over using the e start switch , the display reads 999 888 777 666 ... Right down to 000 and repeats itself . 
       
      He managed to get a parts bike , I changed over the CDI and the coil and the stator from the parts bike and there was another black box by the voltage regulator I changed over ... I used my multimeter to confirm as much as I could works , it's hard without knowing which wires are which , and I cannot find any diagrams online for this bike ? 
       
      Do you think it could be the Killswitch? There's so many wires coming from there I don't know where to start . Also I should mention it appears the fan on the front of the bike has been taken off (the wires have been cut too ) 
       
      If this bike sparked it would run . The previous owner said he parked it one day and it just wouldn't start after.
×
×
  • Create New...