Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Jason Hatton-Fearnley

1996 Kawasaki Bayou 400 gets one spark then nothing

Recommended Posts

have a 1996 bayou 400  with a starting problem 
 

when checking sparkplug grounded to engine

-turn key on, hit starter, get one spark then nothing

-turn key off and back on hit starter, get one spark then nothing

 

Any ideas

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Tagged Content

    • By Ailll1
      I’m working on a Kawasaki Bayou KLF400 for a family member that doesn’t have spark. I’ve already replace the ignition switch and the stator which were defective. The stator had a melted connector and one of the phase had low resistance and low VAC output. 
      What I’ve figured out so far is that I’m not getting 12V to the ignition coil when I turn the key to the ON position. From what I understand, the 12V should come from the CDI. I’ve resistance tested both wires going from the CDI to the ignition coil (Green/white and black/yellow). They are fine. The only 12V coming from the ECU is on the yellow/red wire.
      I don’t have the wiring diagram for the 400 but I’m working with the one for the Bayou 300 which looks pretty similar except for the wire color between the CDI and ignition coil. On the 300 diagram, the yellow/red wire goes to the ignition coil, not the black/yellow… All the other wires color match except for this one. Not sure if that’s normal?
      Thanks!
    • By Bryson Bailey
      Hey I have a Kawasaki buyou I put a new carburetor on it and a brand new spark plug coil and still firing up could you know what my problem is anyone please
    • By 1911Neil
      I had a quad fall in my lap a couple weeks ago. The only things I knew about it was it was a Kawasaki Bayou 220, was in pretty rough shape and was free. I couldn't say no to a fun little project. I've been looking a different ATV forums gathering quite a bit of info and decided this was the one I wanted to join.
      Thanks to this forum, I found the VIN under about an inch of mud and cross referenced it to be a '98. It had been sitting outside for at least 5 years and was told it ran when parked, but had no brakes. Squirrels or mice had been chewing on the handlebar controls and it's generally just kind of beat up.
      So far, I've gone through the carb (not near as bad as I expected), freed up the brakes (will probably need new cables), replaced the spark plug, air filter, petcock and put a new battery in it.
      The gas tank had been empty and looked clean so I put some fresh gas in it and tried to crank it today. I got a neutral light, but the starter button did nothing. I tried pull-starting it and it wouldn't fire. I checked the plug and wasn't getting a spark. I started digging and found some potential issues and some definite problems.
      I have a wiring diagram I found on here but it's just a picture or scan out of a book and hard to read. I don't see a reference to a black/yellow wire, which is my first problem.
      First, it that a factory crimp? One of those wired looks like it goes to the connector in the 2nd pic. Is that just a spade lug type connector? I pulled on it with some needle nose pliers but it didn't seem to want to come off. In the 3rd pic, should there be a fourth wire?
      I've read through and bookmarked the threads Andrew Baker and Arizona have going but I figured I needed to start with these obvious issues first. I have lots of pictures, so if there is something else you want to see, just ask. If I don't already have a pic, I'll take one.
       



    • By Mike Strayhorn
      last year I bought led lights when I was riding my 4 wheeler the lights started getting dim shut off
      now my 4 wheeler will not start the battery is hot everything is dead I checked the fuse and its good 
      would there be another fuse I am missing I'm took the led bulbs out and replaced them with the ones that was in there 
      wonder what meh problem is
       
  • Similar Topics

    • By billyz57
      New to Quadcrazy, Has any Yamaha owners had similar issue?
      1987 Yamaha YFM 350 Starts on Pull, but just spins on starter, and won't start.
    • By Chris2018
      I have a 1996 Kawasaki Mojave KSF250. I have no manual on it and it has a no spark issue. If anyone could give me a hand with this or would possibly have a manual would appreciate it. 
    • By JJ78
      I have a yamaha big bear 400, tested all fuses and relays. When I turn on key I get nothing, no neutral light or headlights. Could it be the key switch bad?
       
    • By JonBat68
      I have a 99 250 Quadrunner. Currently has no spark. It would run for 5 minutes, then shut off. After it cooled down about 20-30 minutes, it would start again. I ordered a new stator and found the old one was damaged (copper windings broken)  I installed the new stator, filled with oil and now it has no spark. Any assistance would be helpful
    • By Nick Gudex
      Hello I am new to this site and I havea problem. I have a 1987 big bear 4x4 that will not spark. I tested pick up coil per repair manual and I tested my new coil both ok. It puts out 9 volts at the coil but It is reversed polarity. So when I hook my meter up to it she shows -9 volts while cranking. When I put a test light  on it it flashes. Being an electric system this should tell me something but I don't know what its telling me. I have yet to meet one i could not fix but this old girl has me stumped. Any help would be awesome. Thanks to all.
      Nick
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...