-
Do you own an ATV? Join our Forum!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
-
Similar Topics
-
By Gilbey
Just got 2018 Suzuki King 400 ASI, getting ready to install winch on it. Noticed the wire loom up front on top of frame to pass wires through but not quite sure where the loom comes out at. I am assuming by the battery but it is not visible........would you guys just wire direct to battery as I had on previous quad or is there a better spot to wire to? I had noticed a wire junction on top of driver rear wheel with nothing connected to it and was curious if my leads could bee run to that? May have to go to dealer to see if a mechanic there can give me some insight to this process. Thoughts and ideas greatly appreciated.
-
By Christine Kiffer-Meany
Hey everyone...does anyone know if tie rod sets for a Honda 250 will fit a 125? My son just snapped the tie rod end clear off. We have a 1987 Honda fourtrax 125. Just want to make sure before I order the set off eBay. Thanks
-
By matthew smith
I have a honda recon 250 that i just bought. the compression is around 90 needs to be rebuilt. im getting into rebuilding it took apart the top end no problem except for the cylinder walls. as shown in the pictures. the way the piston sits in the cylinder is if you were sitting on the wheeler the skirt on the piston is left to right. so the wrist pin is front to back. which is where the two marks are in the cylinder. so that means the connecting rod is making the piston slap the cylinder on the wrist pin side which seems like a weird way for the cylinder to be moving. not natural. now the connecting rod has slight play left to right but not up and down. ive talked to a few people they say it might be the roller bearings in the connecting rod where it meets the crankshaft. but the play it has is not that much. im just looking for some more input before i start splitting the case.
-
By northernmi
View File 1985-86 Honda ATC 350X Service Manual
1985-86 Honda ATC 350X Service Manual
Submitter northernmi Submitted 03/16/2020 Category Honda ATV
-
-
-
Similar Tagged Content
-
By thegipper
Have replaced, Carb, fuel pump, CDI, plug, coil,fuel filter. Will crank but not srt. Getting spark and battery is fully charged 12.6V
Any suggestions????
Thanks
-
By Wali
I was riding my 400ex one day and when i shut it off to put it in the garage i tried to start it put again to drive it into the garge and it wouldnt start.I put a compression tester on it and its like 30 psi with out throttle and 0 psi WITH THROTTLE.
when i put my finger over the hole it fell likes its pulling my finger in more then its pushing it out
Has good spark.When i took it into the shop the said it had 1oz of oil in it and a tiny pit of metal shaving(TINY BIT LIKE 30 flakes)
When i try to pull start (push start/roll start) it made a not normal sound and wouldnt stay running.
If my bottom end is blow why would it still turn over fine,
Are my valves siezed or not working properly
or is my timing off causeing valves to not open in correct order with fire
PLEASE HELP all help is appreciated
-
By Trenton
Hello. I am a new member as of today. I had a quick question to ask. I recently was driving mt HONDA RANCHER 2004 GPSscape 400 and my display stopped working. I was driving the atv and all of a sudden the speedometer and the service lights went out. Also the lights stopped working. I am still able to shift gears, change from 2wd to 4wd, and can still select if I want EPS or Auto. I have checked my fuse box and have changed a few of them around. It did not change anything. I was wondering if anyone had any idea of what had happend. Thank you for your time- Trenton
-
By wHarmon
Our 1988 Yamaha Terra Pro is finally seeing the finish line of becoming our new bush hogging tractor! I've had the terra pro for almost 2 years... we had great intentions, but after removing the fenders, fuel tank, and the carb, we let it sit up. Shame on us! However, the terra pro is cranking today. We cleaned the carb, figured out what goes where and where did that screw go! She smokes like there's no tomorrow, but that's okay! The only issue right now is getting all these lines hooked back up to the carb right! There is 5 lines to hook up to this thing!! And in our moment of drinking and removing parts, we cant remember how they go back on. I've found several diagrams online, but none showing the overall schematics of all the lines! If anyone has a service manual, or any way of helping us figure out what goes where I would really appreciate it!! I can attach pictures later if it'll help!
-
-
Recently Browsing 0 members
No registered users viewing this page.
