Washington Trails and ORV Parks
-
Similar Forum Topics
-
By HSTAR
Hey I have a 1997 big bear 350 4x4
I replaced the shifter shaft and the shift arm linkage and the rod when I installed them all I was unaware that you had to line the dot on the shifter shaft with the gap on the linkage arm gap put it all back together and rode it I can't get it to shift in the right gears I can move the shift cam by hand and goes in different gears but with the shifter shaft in it riding I can't put it in R or N
Anyone know how to line up the shifter shaft and the shift cam s
-
By ResQ91
Hi guys
My 87 Bear 350 won't start and could use a hand.
Turn key on and Oil light turns on and then slowly fades out. (I think this is key to this) No start, not even a tick.
battery and connections good
A Solenoid post jump turns it over
Neutral Safety Switch wire attached and seems good
It has not had a wire/switch on Rear Brake Pedal ever since I had it.
Any thoughts on some other things to troubleshoot this??
-
By utvboard
2009 HONDA BIG RED
Honda enters the MUV (multi-use vehicle) market with a side-by-side machine that leapfrogs the competition to set new standards in utility and recreation. With numerous automotive-based technologies, Big Red features a powerful 675cc OHV liquid-cooled PGM-fuel-injected single-cylinder engine and an automatic transmission with three selectable drive modes plus Reverse, front and rear independent double-wishbone suspension, a roomy cab featuring rubber-mounted bucket seats with adjustable backs, and a specially designed, highly durable, tilting cargo bed. A broad selection of Honda Genuine Accessories will also be offered.
Big Red
KEY FEATURES
- Powerful OHV, liquid-cooled, PGM-fuel-injected 675cc, mid-engine design.
- Automatic transmission with Reverse.
2009 Honda Big Red in Camo
- Three selectable drive modes.
- Front and rear independent double-wishbone suspension for an impressively smooth comfortable ride.
- Roomy cab and rubber mounted bucket seats with adjustable backs designed to comfortably fit a wide range of body types and reduce fatigue on long drives.
Specially designed, high durability, tilting cargo bed
- Specially designed, high durability, tilting cargo bed.
- Wide variety of Honda Genuine Accessories.
- Summer 2008 release. More information to come soon!
Board Message - UTV Forum - Online UTV Community and UTV Forum
-
By John Sinclair
I WANTED TO UPGRADE THE CARBURATOR ON MY 1992 BIG BEAR 350, SO I ORDERED A NEW CARB FROM EBAY. ACCORDING TO THE WRITE-UP IT WAS A GOOD FIT FOR BIG BEARS FROM 1988 TO 1996. WHEN I REMOVED MY ORIGINAL CARB I NOTICED THAT IT WAS DIFFERENT FROM THE NEW CARB MY CARB HAD TWO THROTTLE CABLES THE NEW CARB ONLY HAD ONE CABLE. HOW CAN I MAKE THIS CARB WORK ON MY TWO CABLE THROTTLE? -
By ResQ91
Hi Guys!
New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
I have an 87 Big Bear 350 YFM350FWT
The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
What would you recommend other than a carb rebuild?
Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
Or ??
Thanks in advance for any advice you have!!
Dave
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.