Quantcast
Jump to content

Recommended Posts

Posted

If there is that much coming out, it's like DD said..there is too much getting into the combustion chamber. Have you changed your air filter recently? Just curious...make sure it's not clogged.

Posted

What dd said.also check your dipstick for overfill. And check spark plug. If excessivly oily. Might be time for a valve and/or ring job. How many miles on your unit?

All factors

good luck and good riding

doonorth

  • 6 months later...
  • 1 month later...
Posted

just took one apart doing same thing looks like it need piston rings and a valve job take off the head and look at the valves for soft oil carbon on intake valve and see how slopy the piston is in the cylinder

  • 6 months later...
Posted

first thought,

1.check not over filled with oil.vacuum line could be sucking oil. if dirty drain and replace quick solution could go thicker eg 20w-50 bike oil

2. check filter

3. spark plug what color?

4. compression if on the low side ~120psi its rings or valve. if high could be sticky or broken oil ring( if they are sticky, try SEAFOAM, and or intake cleaner, warm upto temp and add little and rev a little and then add more until it stalls. let sit for 30min and run it until warm and exhaust should stop smoking.

5. take head off check valve guilds.

6. check rings and bore size and roundness

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By Cj Winds
      I have a 2009 Honda Rancher TRX420FA with shifting problems.
      Usually it shifts ok when cold but after couple minutes it will stop shifting with no codes.
      The 1st shift clutch oil pressure when in first gear is 74psi. The 2nd shift clutch oil pressure when in second gear is 74psi.
      The 1st shift clutch oil pressure when in neutral is zero. The problem is when the tranny is in neutral the 2nd shift clutch pressure starts around 10-15psi and builds to 20psi. Is this normal?
    • By Mikey509
      Hey guys, so I've been messing with my quad, and between all the starts, the battery is dead. Is there a certain way to charge these? Can I just throw a trickle charger on it and call it a day? can i also jump it like a normal car with a battery pack or is that to much voltage 
    • By Mikey509
      Hey guys i recently got a old recon 250 up and going and the prev owners had the carb screws all messed up. i was wondering if anyone can give me the basic run downs on if i turn both screws all the way "tightened" how many turns out will the quad run okay so i can then dial it in. the prev owner had the screws messed up so bad it woudnt idle. i got it to idle but idles rough. its super lean any guidence is appreciated 
    • By TomJulio
      Looking for two stock front wheels for 92 TRX300 2WD.   I think they are 6 x11" size.     
    • By gordonmacritchie
      on my honda trx 500 we have no power to the ignition switch for starting or ignition
      we have lights and horn working
      all fuses are fine
      have traced through the harness and cant find any broken wires or bad connections
      from what we have gathered so far the pgm fi unit is not sending any power to the fuel pump relay to power everything up.
      if we put power direct to the ignition switch plug then everything works but wth the key in the off position.
      does this sound like a faulty pgm fi unit?
×
×
  • Create New...