Quantcast
Jump to content

Recommended Posts

Posted (edited)

guys and gals I have a 2002 Kawasaki 650 praire it sparks once on each cylinder then stops i have replace wire harness, CID, regulator some one please help :aargh: and why only 1 time if it was the pickup coil it would not spark at all need help

thank eh

Edited by lamhound
Posted

Did you replace it with a new cdi? There may be sensors on that machine that will limit spark to slow the egine down if let's say the belt was slipping or it had a rollover which could be causing an issue. Usually it would be a cdi or coil issue, I would think.

* Added issue into your thread title.

Posted

A bad pickup coil is not necessarily out of the question, sometimes when they are bad, they will only spark once or twice once the start button is released. They have a tendancy to act very strange when they go out. I would also take into consideration the advise that Ajmboy gave you, there could very well be a sensor or switch that is causing your problem.

Posted

i will try resetting the belt switch or the cvt or what ever they call it i did replace the coil very weak spark like i say will try and re set cvt switch will keep you posted

thank eh

mike

Posted

well boys and gals it looks like i found my problem i changed cvt switch no luck i change the tip over switch no luck replace pickup coil no luck that's when i got real mad :aargh: switch out wiring harness that's when i came to the problem the ( ignition switch) :laugh: it was not push in good and didn't have a good contact put the spark plugs back in boy she run good

man we'll go muddying by Sunday can't wait

anyway thank folk for your input

Michael w

:laugh::laugh::laugh::laugh:

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Popular Now

  • Similar Forum Topics

    • By 88bigbear
      Bought a 88 big bear 350 4x4 took it for a run and lost spark, found it was stator so I replaced that then took it for a long run and it sat for 2 days and no spark again, this time stator tests good on ohms and voltage for source and pick up coils so I started replacing things including regulator, ignition, ignition coil and plug cap, spark plug and everything tests great including all safety switches until the orange wire for ignition coil from the cdi it only reads 3 volts so I replaced the cdi and still 3 volts, any ideas??
    • By cfherrman
      Fixing for a friend. Atv was at a different friends house to be fixed and he rebuilt the carb and had it running nice, then it shut off and no more. He replaced the key and the coil.
       
      So he got busy, so I am helping, I checked the wiring from the stator to the cdi, and from the cdi to the coil. All is good. I checked resistance on the pickup coil, good, and on the source coil, open. I buy a new stator (China) and the 4 prong plug only has 3 wires in it while mine has all 4. I checked resistance in the source coil and it's in the 300's. I pulled one of the old pickup wires out of the old stator and wire it in the new one. Still no spark.
       
      Why do the wires differ, I checked the VIN again and it's "J" for the year and I got a 1988 stator. Please help!
    • By LashinWheeler
      Hello all, I have a 2006 Polaris Sawtooth with no spark. It has a dead battery but with a jump pack on it, it will still not Spark. Plug is good, Throttle ETC is not closed, Stator pick up coil seems to Ohm out in the correct range, Unsure how to properly check the CDI. And when ignition is on the Neutral and reverse light come on but after cranking just the neutral stays on. 
       
      Any help would be great,
       
      Thanks!
    • By TomJulio
      My 1992 TRX00 recently stopped firing.  I understand this is a common problem. I have ordered an aftermarket CDI unit.    TJ
    • By tflack500tbx
      Background,
      This winter (Dec.) I was plowing and everything just died, just quit.  No lights, no pull start, No nothing.  I've had this problem before and I changed the voltage reg and it ran fine for over a year. Then this.  So I changed it again, thinking this was the same problem.  Tried to start it and a small pin hole in the CDI appeared with electrical smoke.  
      Months go by and I finally decide to just replace parts (I'm Horrible at electrical issues).  I changed the stator, new CDI, new Voltage reg, new starter solenoid, tested the starter (prefect), charged the battery.  
      Went to start it and the solenoid rapidly clicked.  All the dash lights on, headlights work.  Pull stared it and it fired right up no issues.  Looked into the rapidly clicking starter solenoid and it was not enough juice in the battery.  Took the battery completely out and hooked up a jump box to it turned the key, light on, everything looks good.  Pushed the starter button and it fired right up ran great.  Turned it off to test it again, Turned the key and nothing.  No dash lights nothing.  Took the jump box off and pulled started it.  Started it right up.  Re-hooked the jump box, still nothing.
      Any Ideas? 
×
×
  • Create New...