-
Similar Forum Topics
-
By Admin
Does anyone use GPS, whether on a device or app to record their ATV trail rides? I have been thinking about a section where our members can upload let's say a .gpx file and share their rides on a google map for others to see where there are riding areas. Not sure if this is something of interest or how much it would be used, so just trying to get an idea.
Importing routes from files like xml, lmx, tour, freshroute, gpx, kmz, kml
-
By BillR94
I picked up this ATV that had no spark. The previous owner said he was driving it and it died and would not start. He discovered it had no spark. He replaced the CDI and the coil with no luck. He got tired of it and I bought it. I replaced the stater and now it has strong spark. Now, it starts for a second or two then dies. It will not stay running. I have checked the timing and it is spot on. The valves are adjusted correctly. I see no warn issues with the cam. I put the original CDI and coil back on it. Same problem exists. Compression is at 65 psi (has decompression mechanism),
I took off the muffler in case the issue was clogged pipes. No change. I replaced the spark plug. No change. The carb was an aftermarket so I put a Niche carb on with no change. I bypassed the fuel pump and that did nothing to solve the problem.
I don't know if this is a carb issue or an ignition issue. I am looking around locally for an OEM carb to try out but not sure that will fix the problem.
Can anyone help me solve this problem. I am running out of ideas.
Thank you for your time
Bill
-
By BruinBeater
Hey all, BruinBeater here. Just joined up from the Pittsburgh, PA area.
Got a Polaris Sportsman 1000 and a 570 in the garage that don't get ridden quite enough but looking forward to a family trip this fall.
I'm the unofficial mechanic of the extended family. In the past month or so I've replaced a transmission in a Chevy Silverado, rust repair on a Chevy Malibu, electrical repair on a Subaru Crosstrek, overheating issue solved on a Can Am Commander, and right now I have a pair of Grizzly and a Bruin 350 in the garage. Both have a no start condition and have been sitting for 2+ years.
-
By Rick Shropshire
I’m looking at replacing rear brake calipers on both of my blasters. I was told that the only thing available was a hydraulic upgrade? I’d prefer the original. Anyone?
-
By Gwbarm
I decided it was time to do the brakes on the Eiger, i got it a couple of years ago and worked out all the bugs got it running good and ignored the brakes. None on it ,front or rear. Decided to attack the front first no pressure on the master cylinder and screws were stripped out on the reservoir, took the banjo bolt loose and pure water ran out, glad i didnt wast time on drilling the screws out, pads were shot also. Pulled a couple out of my box o parts. One was for right hand so wouldnt work, the other looked fine until i opened the reservoir and full of white powder. Cleaned it out anyway and tried it, only would build up a minimal amount of pressure. So no go on that one. So ordered new master cylinder and pads, so now i have to hurry up and wait.
On to the back they are drum brakes so i knew this would be fun, 20 year old machines that have been mudded and abused for that length of time nothing comes off easily. The engage shaft was froze solid from corrosion. Getting that out is easy but you have to get to it first.
The center nut was supposed to be 30mm but it wasnt it was 27 the only size not in my large set, go figure,
The previous owner decided it was a good idea to JB Weld the cover on making it near impossible to get off, had to chiesel it off.
The mounting plate was a different story, nut was tight tight tight took my biggest impact two or 3 times hammering on it to get it loose after soaking all night in PB Blaster. Got it moving along the splined shaft easily but wouldnt come off, when it got to end of its run it would just stop, ended up using 2 24 inch pry bars one on each side, past the point of being gentle and it finally came off.
Got to the drum and it came off easily a little suprised at that, it was full of mud and rust, i knew it was going to be bad because there was a snorkle on it when i got it, never buy one with a snorkle, they are highly abused to the machines limit, but i got it cheap .
Finally got in there and no shoes left and a complete mess.
Lots of mess to clean up.
Got it looking a little better.
Lots of cleanup later! Waiting for new parts.
-

Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.