Quantcast
Jump to content

Recommended Posts

Posted

:no:

We have a 1998 Polaris Xplorer 300. Havn't had it running for about a year. It cranks, has good spark but will not satart without starting fluid. 1 shot in the carb, full choke on and it starts and runs, on very high idle for about 45 seconds then quits. Another shot of ether and it starts again and again shuts down. I can't slow down the idle using the idle screw on the carb. and when I move the chock lever to middle or off, it still shuts down. Any ideas from the xperts?

Posted

the reason it runs on high idle then quits is because it is on straight ether. You r not getting fuel intothe carb. i would start with cleaning the fuel tank and lines and carb. also rebuild the diaphram pump and check your pet cock. if that is all ok then i would say that you have a vacumm leak causing your vacumm fuel pump not to work.

Your friendly neighbourhood mechanic.

Posted

Well, I took the carb apart and found nothing visibly wrong with it. Didn't check the petcock. Not to sound like a complete doofus but where is the diaphram pump located excatly?

Posted

first of all why trying adjusting something u not professional do you. after long stops just drain old fuel try to run without spark plug .u answer u question was running a year ago the vaporises.if u adjust something remember what u did .the carburetor made of aluminum from long period of time hi gets corrosion in side .but if cleaned already so u good.sorry for my English. good luck

Posted
first of all why trying adjusting something u not professional do you. after long stops just drain old fuel try to run without spark plug .u answer u question was running a year ago the vaporises.if u adjust something remember what u did .the carburetor made of aluminum from long period of time hi gets corrosion in side .but if cleaned already so u good.sorry for my English. good luck

I agree, drain the old fuel if it has been sitting for a long time. I still feel that carb needs a rebuild.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Thekevinjb
      Can anyone provide information on connecting a hitch to a Polaris. Anyone know where they sell small trailers for my quad. 
      thanks
    • By RGS
      1989 Moto 4 YFM350ERW intermittent spark.
      Quad has set for about 7 years and was running when parked.  When I replaced the battery and attempted to start it had no spark. 
       
      What I have done.  Followed troubleshooting in the manual. 
      1.       Coil failed the resistance check so I replaced it.  Still no spark.
      2.       I performed resistance checks on the stator and they all pass.
      3.       Found a bad rear brake stop switch and unplugged it and connected the wires in order to disable.  Now I have intermittent spark.  I believe that the issue is with either the stator or CDI and not sure which.
      1989 seems to be a transition year for electrical.  I can get new aftermarket CDI units for 87-88 and 90-94.  I cannot get ones for a 89.  I can get new stators for 87-89 and 90-95.  Looking at the schematics the wiring on my moto is closer to the 90 ones on the ATV side of the CDI and closer to the 87-88 on the stator side of the CDI.  Looking at part supply sources the stator housing is the same part # for all the years and looking at some of the stators on Amazon that have the dimensions on them both of the stators are the same size.
      What I am thinking of doing is to replace the stator and CDI with a 90-95 one as these parts are all readily available.   Does anyone know if this has been tried before and if there are any issues with doing this.  
       As a side note I also have a 1993 Moto 4 YFM350ER that has been sitting longer but it is located about 400 miles from me at this time.  By doing this change in addition to being able to get parts I will also have 2 ATV’s that are the same electrically. 
    • By Atomusthenes
      I would appreciate being pointing in the correct direction for a wiring diagram and or schematics of the 88 Honda FourTrax 300 4x4 if anybody has any knowledge of how to test the ignition system stator and CDI I don't know if the voltage regulator probably and also the FCU I put a new ignition in it it is a cheap aftermarket one doesn't have the correct plugs but has the correct wiring scheme I get power  the neutral light comes on and the oil light stays on it turns over but I have no spark
    • By BuckBilly
      Good morning to all !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
      Let's see if we can make this a daily event.
    • By Memphis
      Not sure if in right place but here goes
      My 300 is lacking power only reaching 30mph and struggling uphill everything else seems ok other that this problem cleaned all fuel new filter pan and all new fuel pump and spark plug full oil change is there anything I am missing
      ps It is auto and does noy seem to want to get in another gear 5200 rpm at 30mph
       
      Regards
×
×
  • Create New...