Quantcast
Jump to content

dctaz37

Members
  • Posts

    46
  • Joined

  • Last visited

Everything posted by dctaz37

  1. I recently replaced the oil in my ATV and now I smell oil burning which it didn't before. I used automotive 10w30 full synthetic. I used the same oil on the previous oil change without issue. I had researched the oil before to decide if I needed to pay up for ATV oil and there were many posts that stated automotive synthetic oil would be fine. Now I'm not sure what to do. The only thing I did different this time was replace the filter cartridge rather than clean it and I believe it was the same brand of oil.
  2. I replaced the shoes on back and both fronts. Seems better but still not great. The adjusters on the front were all seized and a real pan to free up. One ended up getting a warp so it doesn't work very well now. I got it together as well as I could but really hard to adjust the shoes. Especially when it is full time 4x4 so when you turn the wheel you get the resistance of the other wheel etc...
  3. I adjusted the brake handle and when I engage the brakes the handle still has a lot of resistance but the brakes don't stop well. I saw another post here with the same issue and they suggested to adjust the shoes. I took my brakes apart and the adjusters are seized. I tried to figure out how they work so I loosened the side that is in the wheel cylinder and removed it but there is no thread to go in or out so I don't know how they work. I sanded the pads a bit to get them rough. Reassembled and same issue.
  4. Thanks, I checked the front brakes and pads look okay. Not sure why stopping isn't very good.
  5. Hello, the ATV doesn't stop anymore so I guess it is time to replace the brakes. Looking for part number and instructions. I think it may have shoes front + back and the front would be hydraulic.
  6. dctaz37

    dctaz37

  7. Is my ATV too old or does this part not fail? I'm surprised I have not got a response by now.
  8. My ATV started making a rubbing and clunking noise. I took the skid plates off and found that the front u-joint on the shaft that connects the front axle to the transfer case is toast. My manual does not reference this repair. Looking for instructions.
  9. I am assuming it is leaking from the overflow. Took the carb apart and it is clean inside. Put it back together and gas leaks out the host at the bottom. Tested to make sure the drain screw is not the problem when I had it off.
  10. I was out the other night for a few minutes and noticed the exhaust close to the motor was bright red. I searched the internet and saw suggestions that it may be running lean. Could this be it? How do I correct this?
  11. I have not had the cover off yet. Which side is it on? How does it come off?
  12. Do you have a picture? From what I have read there is no switch and you need to ground a green and white wire out of the CDI. The side effect is no reverse light.
  13. When I back up with a load on the atv makes a sort of muffled backfiring noise and does not seem to have very much power. Any ideas?
  14. Okay all is well. Reduced the air from 20 to 3.5, adjusted the rear mount lower and used a ratchet strap to put some load on the atv from the blower bracket.
  15. So what do I do? Will shock spacers help? Is this a good idea?
  16. Okay I did a little more digging and found that there is very little clearance if any between the support that attached to the ball and the bottom of the atv. Should there be clearance? If yes then how much? I also raised the blower legs because the blade was right on the ground. I tried the ratchet strap but there is no give because the support is basically on the bottom of the atv. I also noticed the guy has 20 psi in the tires, I think iot should be 3.5.
  17. He only used it twice because he didn't like it. My driveway is gravel and right now it is packed slushy snow. I guess it cant be used in any packed conditions and when moving it around the guide wheels are always down and get hung up on things.
  18. I just bought this blower mounted on an 05 Kodiak. I tried it out and my drive is soft and the guide wheels seem to dig in and the ATV gets stuck everywhere. Anyone familiar with tis? Is it setup wrong? Any advise would be appreciated?
  19. They didn't seem to have the bulb I needed. Dealer wants $12.99. Found it at napa autoparts for .74 but need to buy 10. Still ahead of the game. Im buying an ATV snowblower 15 hp mounted to the Kodiak. It is going to work out to 3800 for ATV 2300 for blower, new battery, winch and comes with a second seat and tool box. I think it is a descent deal.
  20. Okay thanks for the info. Another question, Where can I buy parts online for a descent price with shipping. I just need a bulb at this point.
  21. I am in Ontario, I did check around on the internet and couldn't find very much. I have a 98 big bear. I will look for the obvious signs but I guess there is still a bit of a gamble. Any ball park on the price?
  22. I hope this is the right spot. I'm looking at buying a 2005 400 4*4 Kodiak and wanted to know what to look for, how to check the mileage as there is no odometer and value.
  23. Yes dialup is a trade off for country living. I could get high speed but it isn't worth the price. The atv is a 2 stroke 4*4. Thanks.
  24. I'm on dialup so I figured I would try this forum first. I can get the manual for around $50 at the store so I thought I might do better online. I figured out the oil already.
×
×
  • Create New...