Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

ATVNetwork

A Simple Way To Mount Devices To Your ATV Or UTV

Recommended Posts



I bought a RAM mount for my obsolete Garmin GPS unit and it has worked very well. This is for the vehicle, not the quad.

 

Mike

 

Share this post


Link to post
Share on other sites

I was thinking of some kind of mount for my phone to my grizzly. Haven't landed on anything yet...

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Palooza
      Headlights on my Outlander 570 are junk.  Would like to upgrade to a light bar.  What is the max size (wattage) that it can handle? 
      Can I just split into the high beam wire for an install.  I see YouTube videos of a separate switch that hooks up straight to the battery, but wouldn't that drain the battery if the machine is off and lights cold be left on by accident.
      I'd like to hang it from the front rack as I have a basket installed on the rack that I would like to keep there.  If anyone has done this, please send a picture!
    • By jimybud
      Below is a quote from a response to similar question from yesterday: 
      "Easiest thing to check is trash in the main jet.  if it idles fine, then the idle circuit and low speed jet is clear.  if it bogs off idle that's when it's transitioning to the main jet." 
      I will go ahead and open up the carb and check the main jet, but please respond to this post as if the main jet is squeaky clean.
      Below is my post:
      Only starts and runs on Full chock. 
      Does not matter what position I have my "mixture" screw.   Tried it at zero, 1 turn, 2 turn, up to five turns.  Spent a few hours confirming that the position of the mixture screw does not resolve issue.
      Runs great at idle and if I slowly engage throttle, it will rev up as expected.  But, quick rev up or when I am trying to drive it, it spits and sputters and looses power.
      I also use a propane bottle and did not find any obvious leaks, and the vacuum port is hooked to fuel peacock and I also made sure to simply block the port with my finger to see if that would resolve the issue.
      New Carb (after market), New Coil, Fresh Gas.  No leaks at manifold boot, hot battery.  Good gas flow.    Runs too good to be a valve issue, or cylinder, great compression.
      I can move the choke out a tiny bit, and it will still run, but will still bog down when I try to power it up.
      I also have a 250 trail boss Polaris that I require to run at full choke, but it has power at all throttle potions.
      I suspect it is running rich as the choke is on, but will not run with it off.
      Any details would be appreciated.
    • By Andrew VanHouten
      Got a 2007 Polaris Sportsman with this plow mount but no plow. Having a hard time finding a plow that will work... Anyone recognize it? Looks like some kinda quick clamp or something.
       


    • By Admin
      Looking for Yamaha ATV VIN (Vehicle Identification Number) Number Decoders? Once you find your ATV VIN number off the tag on your Yamaha ATV, you can go to all kinds of websites that have VIN Decoders available. The best ones are backed by the Yamaha ATV manufacturer, however there are plenty of aftermarket Yamaha ATV VIN Decoder websites on the web. This topic will stay pinned and if you find any to add, please do it with a reply. 
      The following Yamaha ATV VIN Decoder websites are available where you can just enter your VIN number and it will shows you some of your ATV model details:
      CycleVIN https://www.cyclevin.com/
      KBB.com https://www.kbb.com/vehicle-history-report/
      CARFAX https://www.carfax.com
      autoDNA https://www.autodna.com
      VinAudit http://www.vinaudit.com/
      decodeTHIS https://www.decodethis.com
      VINCario https://vindecoder.eu/
      NICB Theft Check https://www.nicb.org/theft_and_fraud_awareness/vincheck 
    • By Ben Cramp
      I am hoping one of you knowledgable people can answer this for me. I have a yfm200 moto 4 engine I want to put in an off road go kart. I would like to mount a sproket where the drive exits the case before the u joint so that I can get rid of drive shaft and make engine bay compact. To do this I would mount engine 90° to axle but would also need to tilt it forward 15° to account for the angle the drive exists rear of casing. Would that be ok? Would oil pump etc still work. Any advice greatly recieved.

  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...