Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

afa913

Honda 400ex rear carrier

Recommended Posts



It depends, if the bearings pop right out and the old one is not worn or getting oval then leave it be. 

Me personally, since your going to have it  apart I would replace the whole thing. It’s a smal expense in the overall project and a main part of the drive train.  Just make sure it’s an oem replacement part.  

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By George MacDougall
      Bulldog truck bed ATV carrier - Haul 2 ATV’s with a short bed truck and tow a trailer! 
      I am selling my Bulldog truck bed ATV carrier for $750. This rack slides into the back of a short bed (6.5') or long bed truck and allows you to rear load and haul 2 full size ATV's, and tow a bumper-pull travel trailer at the same time. I purchased the rack about 10 years ago from a dealer in Eugene, OR. When stored it has always been covered with a tarp. Now we only have one ATV which I carry in the truck bed so I no longer need the rack. This rack is stoutly built and all welded together, unlike other flimsy carriers currently on the market. Bulldog Manufacturing out of Marysvale Utah quit making them about 5 years ago. It includes two 12 ft. aluminum folding ramps that store under the ATV's. Also included are four heavy duty ratchet tie downs for each corner of the truck bed, and six over the wheel tie downs to secure two ATV’s to the rack. The measurements of the rack are:
      Base – base of rack measures 73" long, 47" wide, and 23” tall.
      Deck – deck of rack measures 80” long and 102” wide.
      My name is George and I am located east of the Sacramento CA area, pick up only.  If you’re interested or have any questions, please text me or call me at 916-826-5587.  Thanks!






    • By Austin Rowedder
      Hi I have a 2007 Polaris outlaw 525 irs and am trying to replace the needle bearings in the rear a arms. I was wondering how you go about getting the rubber seal and bearing out!?
    • By Thunt56
      How do I replace the pinion clutch shaft in a 1987 Suzuki LT230 quadrunner? It starts up on the first kick but when I put it in gear it wants to kick up. I can give it gas and put it in gear but my clutch lever isn’t doing anything. SOS
  • Similar Tagged Content

    • By Justice Owens
      Hey guys, any ideas would be greatly appreciated on this. 
      So it started a few months ago, riding with some buddies and my 400ex all of a sudden lost power. Wouldn't fire, wouldn't sputter. Towed it home, and then it fired right up. It continued this pattern for a week or two, ran perfectly for varying amounts of time, suddenly died, and would start right back up if I waited 20 mins or so.
      Now we get to the next phase... I was dinking with it one day, I think I pulled the carb off and cleaned it out, (not really dirty but just to be sure) and I was trying different fuel screw adjustments. At any rate, I didn't notice much change, except obviously running a little poorer when I had the fuel screw in the wrong place. I took it on a quick ride around the block, and it was just fine. Ran awesome, had lots of power, etc. Then went around the block again and it died on me this time right as I revved it. Ever since then I haven't been able to get it to start. 
      Now when I turn it over, it sputters, fires a touch, but won't start. Ever. I replaced the plug, CDI, and coil, with no change. I do know that it has spark, but I don't know for certain that its big enough. After replacing these with no change I popped the carb off and tried firing it up spraying some either right into the intake. Upon doing so, it revved right up, but obviously there was no carb so it didn't stay running for long. While spraying the ether it seemed to run just like other engines I've tried spraying ether into no popping or backfiring etc. When it fired right up on the ether, I figured I must have a carb issue, so I just bought a whole new carb instead of taking the old one apart for the 800th time. When I put it in, there was no change whatsoever. Still turns over and sputters, but won't fire up.
      I am completely befused, and any input would be graciously accepted. If you read through all that your a trooper, so thanks very much :) 
    • By Bob Hill
      I need a motor but i really dont hsve lots of cash and im on the kenai peninsula. Up here in Alaska i really need help
    • By Wali
      I was riding my 400ex one day and when i shut it off to put it in the garage i tried to start it put again to drive it into the garge and it wouldnt start.I put a compression tester on it and its like 30 psi with out throttle and 0 psi WITH THROTTLE.
      when i put my finger over the hole it fell likes its pulling my finger in more then its pushing it out 
       
      Has good spark.When i took it into the shop the said it had 1oz of oil in it and a tiny pit of metal shaving(TINY BIT LIKE 30 flakes)
      When i try to pull start (push start/roll start) it made a not normal sound  and wouldnt stay running.
      If my bottom end is blow why would it still turn over fine,
      Are my valves siezed or not working properly 
      or is my timing off causeing valves to not open in correct order with fire 
      PLEASE HELP all help is appreciated 
    • By Coral Breding
      I loosened the allen bolts on the carrier and when I went to put my driver in the alot to pull back and tighten the chain, I noticed the holes were facing the front of the bike. I tried to slide a driver in and tighten the chain but the thing would not budge. I nearly ripped the tip off the driver in the slot. Any suggestions? 


    • By afa913
      Anyone know a place i can find a used stock pipe for a 400ex?  I would love to find a take off
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...