Quantcast
Jump to content

Carb Replacement (90cc Arctic Cat DVX/Kymco)


Recommended Posts

Morning All,  Wondering if anyone has had any success using aftermarket carburetors on the smaller ATVs?  Picked up a couple Arctic Cat DVX90s over the weekend (2006 & 2008), and one of them has an aftermarket carb that needs to be replaced (it's missing the brass barb for the fuel line ).  Both are the same Kymco power plant, but different frame/body.

I swapped carburetors between the machines to test opreation.  Both ran great, and seem to manage the electronic choke properly. 

Am I better off to buy the replacement carb from AC ($250), or try an aftermarket?  Part of me wants a manual choke.....

Thanks in advance for any thoughts.

Link to comment
Share on other sites

Aftermarket carbs are a much repeated topic here at Quadcrazy and will be a talked about topic forever! Many times here we’ve spoke about them and the general census is that they are not very good.  One of our memebers @JacobSlabach has mentioned that they needed to be adjusted way out from the spec position and has gotten them to work.   But the way I see it, if the quad is worth it then put an oem carb on. I always check eBay for a used oem.   

  • Like 2
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Gwbarm
      I Ran across this video today comparing an aftermarket to OEM Carb on Suzuki Vinson, thought it might generate some interest, it is quite long but informative.
       
    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
    • By Its-always-something
      Have a 1998 AC 300 2x4, Just installed a new carburetor. Engine starts easy but the choke RPMs are very hi and take along time (5-10 mins when cold out). After engine has warmed up choke releases and it idles and runs fine., It does no have an electric choke. The choke lever is never used and it seems like an auto choke? Long story short, how can I lower the choke rpm levels?
       
      Also, carb came with a spare145 jet, not 100% sure what is installed. Could this impact choke RPMs?
       
       
      Any help and information greatly appreciated.
    • By Admin
      View File 2006-2011 Honda Rincon TRX 680 FA/FGA service manual
      2006-2011 Honda Rincon TRX 680 FA/FGA service manual
      Submitter Admin Submitted 04/09/2024 Category Honda ATV  
    • By Charlesbrown
      I’m looking for a top end kit for a Yamaha. I would like to see how well the engine runs before spending $6-$7 hundred on oem. Niche has complete kits from $1-$2 hundred.  Anyone have experience with Niche or similar Chinese companies? 
×
×
  • Create New...