Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

David Miller

Polaris 2018 sportsman check engine light

Recommended Posts

Does anyone know how to access the check engine codes on a 2018 450 sportsman. Just changed battery and spark plug . It runs fine but the light is on and I need this to plow snow and need it reliable. Any ideas . Thanks

Share this post


Link to post
Share on other sites

For my 2018 570 (may be it's the same ), i have to press and hold "Mode" button to see "Diagcode" on the display.

  • Like 2

Share this post


Link to post
Share on other sites

Helpful info here, I have an 07 sportsman 800 and it was different for the older models.  @David Miller, did this help you resolve your issues?  What was the code for?

Share this post


Link to post
Share on other sites

Anyone know where I can find service manuals for Polaris Sportsman? Specifically 2014 550.

My Sportsman 550 has code = 520269-4

I can't find any info on it. Does anyone know what this code means?

Share this post


Link to post
Share on other sites


On 2/13/2020 at 3:04 PM, Powder Coater said:

Anyone know where I can find service manuals for Polaris Sportsman? Specifically 2014 550.

My Sportsman 550 has code = 520269-4

I can't find any info on it. Does anyone know what this code means?

The only 550 manual we have in the downloads section are:

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Tagged Content

    • By jwline
      Friday evening went riding, rode for a good hour or so everything was fine. I went to take a short ride to the restroom (less than 100 yds away) and all of the sudden everything flickered and then just died out. Accompanying the problem I noticed the killswitch completely locked up. Once daylight hit took the killswitch apart to find it had shorted out and melted the plastic inside. Has anyone else had anything similar to this and if so what did you do to fix the situation? I have a new killswitch on the way to replace the obvious problem but was wondering could there be a bigger issue at hand. We tested with a voltage meter to make sure everything was still getting power from the battery and as far as we could tell it was.
      Any advice/info would be GREATLY appreciated.
      Thanks.
    • By bodon
      Anyone know what the fuse terminal marked UNSWITCH  does  .  Even with the key off it is causing a drain on my battery and I'm trying to figure out  what that terminal goes to.  It's a 10 amp fuse. If I pull it the "short" goes away.  Thanks in advance.
    • By Outkast7222
      Had a spark-plug break off, had to pull the head to get it extracted. Where the heck is the timing mark on the crank? Do I need to pull the stator or flywheel to find it? When I pulled the head I had the mark on the cam lined up pretty good but I cant remember if it was perfect and don't want to reassemble a tooth off and have to go back through the bear of pulling this thing back apart.
      Thanks guys!
    • By Chase Cook
      Hi I just got an Polaris sportsman 500 4x4 ATV the other day. I got it real cheap but I started to go into it because it didn't have compression so I bought a new piston and ring kit for it and installed it, but now when I try to start it all it does is shoot fire out the exhaust or the intake of the carburetor. And a timing is top dead center.;I think I can't really tell another way if it is or not. when I put it together I made sure to piston was on top and the cam lobes where facing down where are the cam sprocket is facing up. It has gas and spark. It did start a couple minutes ago but it didn't stay running and now it won't start. Do you think the valve need to be adjusted more to close better?I'm fixing to try that out and if that don't work what is the problem? Also I made sure everything was together good and right and change the oil and changed out the radiator fluid.
    • By Brian Sosebee

      I just rebuilt my 03 sportsman 400. Put everything back together added oil per the manual. Pinched off the oil tank vent line 2" away ran for 45 seconds then cut it off. Check oil level and it was still way high so I wasn't confident that it primed so I did it again. Checked again and it's the same. Remove the oil filter and it is dry. I did the procedure again and the same results.

      I'm worried to keep trying this as the only oil in the engine is what I used to lubricate the parts when reassembling the piston. The crankcase was drained as well.
      I Removed the oil tank and checked all the lines for obstructions and the screen filter and the vent hose and everything is clear. I even pulled a small vacuum on the oil tank while it was pulled off to make sure there were no leaks. The dipstick cap was on tight so I'm not sure why this thing is not priming.

      Anyone have any suggestions. I thought about pre-priming the oil lines from the oil tank to the crankcase to hopefully help the system prime. I'd like to be able to add some oil to the crankcase to so I wouldn't feel so bad about running the engine for another 60 seconds without oil. I dropped just a little bit of oil in the spark plug hole to help condition the sleeve right now.

      What do I do? Anyone had or heard of an oil pump failure on these. Btw oil pump is working fine before I did the top-end rebuild and the oil pump was not touched.

      Please help!!! Thanks all for any and all help.
  • Similar Topics

    • By VikingTrad3r
      picked up my third timberwolf 250 for my daughters.  these are great light weight little quads.
       
      have a strange one for you.  the quad will NOT start in neutral.  it will start in first. 
      if i lift up on the gear selector just enough to hear the little click (its not loud, sounds like a contact clicking, perhaps the neutral safety switch?) the light will go out, but it won't yet be in first either.  that is how i have shown my daughter to start it and she can.
       
      id like to carry out whatever repair is needed.  i have the pdf of the shop manual but it doesn't really have a flow through diagram.
       
      any help appreciated!  thank you.
      i need to add something.  it feels like i can switch into another gear BELOW neutral.  
      so if i switch to neutral, i can keep pushing the gear selector, and it has another click below the neutral.  the light stays on, and when i pull up into first it kind of feels like it has two positions it moves through to arrive at first.
    • By redneck999
      i am sure some one has switched from the dinky battery to a larger car car battery, so any advice? ive got enough bits and bobs on my atv that i feel i need to step up, i keep a float charger on it but i left it unplugged for about a week and it was dead and it a fairly new battery from advance auto, im probably gonna add a cb radio in the future and i think the only thin that has a constant draw is the clock in the dash and the memory for the stereo
      2012 cf moto x5 500 lwb
    • By Chris2018
      I have a 1996 Kawasaki Mojave KSF250. I have no manual on it and it has a no spark issue. If anyone could give me a hand with this or would possibly have a manual would appreciate it. 
    • By technofarmer
      Hey there, i have recently put a new drive belt on my 11 Polaris Sportsman 500 H.O.    It has 44 miles since putting the new belt on and should be nearly broken in as i hear it takes 50 miles to do so?  Anyhow it has had a little trouble with slipping since i put the new one on a few months ago. Now whenver i go down a hill the belt seems to be getting caught in one clutch if not both and then it has to run a high rpm just to go a low speed.  Today it did that again going down hill, i stopped, put it in neutral and when going back up the hill i had to turn it off, put it in neutral, let it roll back down the hill a little, then restart it, low range and it was slipping but thankfully i was able to make it up the hill. 
       
       So what might the problem be? Is this a need for another new belt? New clutches and belt? Or just get something else? BTW the brand new belt i put on it, is a factory one, an exact replacement for the original.   

    • By JonBat68
      I have a 99 250 Quadrunner. Currently has no spark. It would run for 5 minutes, then shut off. After it cooled down about 20-30 minutes, it would start again. I ordered a new stator and found the old one was damaged (copper windings broken)  I installed the new stator, filled with oil and now it has no spark. Any assistance would be helpful
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...